(PDF) A8R32-MVP Deluxe - Asusdlcdnet.asus.com/pub/ASUS/mb/socket939/A8R32-MVP... · viii Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power

Mot

herb

oard

A8R32-MVPDeluxe

i ii ii ii ii i

Copy r i ght © 2006 ASUSTeK COMPUTER INC . A l l R i ghts Rese rved .Copy r ight © 2006 ASUSTeK COMPUTER INC . A l l R i ghts Rese rved .Copy r ight © 2006 ASUSTeK COMPUTER INC . A l l R i ghts Rese rved .Copy r ight © 2006 ASUSTeK COMPUTER INC . A l l R i ghts Rese rved .Copy r ight © 2006 ASUSTeK COMPUTER INC . A l l R i ghts Rese rved .No part of this manual, including the products and software described in it, may be reproduced,transmitted, transcribed, stored in a retrieval system, or translated into any language in any formor by any means, except documentation kept by the purchaser for backup purposes, without theexpress written permission of ASUSTeK COMPUTER INC. (“ASUS”).Product warranty or service will not be extended if: (1) the product is repaired, modified oraltered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) theserial number of the product is defaced or missing.ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS ORIMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OFMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITSDIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSSOF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUSHAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT ORERROR IN THIS MANUAL OR PRODUCT.SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FORINFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, ANDSHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITYOR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.Products and corporate names appearing in this manual may or may not be registeredtrademarks or copyrights of their respective companies, and are used only for identification orexplanation and to the owners’ benefit, without intent to infringe.

E2420E2420E2420E2420E2420

Revised Edit ion V2Revised Edit ion V2Revised Edit ion V2Revised Edit ion V2Revised Edit ion V2January 2006January 2006January 2006January 2006January 2006

i i ii i ii i ii i ii i i

ContentsNotices ............................................................................................... viiSafety information ............................................................................ viiiAbout this guide ................................................................................. ixA8R32-MVP Deluxe specifications summary ...................................... xi

Chapter 1:Chapter 1:Chapter 1:Chapter 1:Chapter 1: Product introductionProduct introductionProduct introductionProduct introductionProduct introduction1.1 Welcome! .............................................................................. 1-11.2 Package contents ................................................................. 1-11.3 Special features .................................................................... 1-2

1.3.1 Product highlights ................................................... 1-21.3.2 Innovative ASUS features ....................................... 1-4

Chapter 2:Chapter 2:Chapter 2:Chapter 2:Chapter 2: Hardware informationHardware informationHardware informationHardware informationHardware information2.1 Before you proceed .............................................................. 2-12.2 Motherboard overview .......................................................... 2-2

2.2.1 Placement direction ................................................ 2-22.2.2 Screw holes ............................................................ 2-22.2.3 Motherboard layout ................................................ 2-32.2.4 Layout Contents ..................................................... 2-4

2.3 Central Processing Unit (CPU) .............................................. 2-72.3.1 Installing the CPU.................................................... 2-72.3.2 Installing the heatsink and fan ................................ 2-8

2.4 System memory ................................................................. 2-112.4.1 Overview ............................................................... 2-112.4.2 Memory Configurations ......................................... 2-122.4.3 Installing a DDR DIMM ........................................... 2-142.4.4 Removing a DDR DIMM .......................................... 2-14

2.5 Expansion slots ................................................................... 2-152.5.1 Installing an expansion card .................................. 2-152.5.2 Configuring an expansion card.............................. 2-152.5.3 Interrupt assignments .......................................... 2-162.5.4 PCI slots ................................................................ 2-172.5.5 PCI Express x1 slot ............................................... 2-172.5.6 Two PCI Express x16 slots ................................... 2-17

i vi vi vi vi v

Contents2.6 Jumper ............................................................................... 2-192.7 Connectors ......................................................................... 2-20

2.7.1 Rear panel connectors .......................................... 2-202.7.2 Internal connectors ............................................... 2-22

Chapter 3:Chapter 3:Chapter 3:Chapter 3:Chapter 3: Powering upPowering upPowering upPowering upPowering up3.1 Starting up for the first time ................................................ 3-13.2 Powering off the computer .................................................. 3-2

3.2.1 Using the OS shut down function ........................... 3-23.2.2 Using the dual function power switch .................... 3-2

Chapter 4:Chapter 4:Chapter 4:Chapter 4:Chapter 4: BIOS setupBIOS setupBIOS setupBIOS setupBIOS setup4.1 Managing and updating your BIOS ........................................ 4-1

4.1.1 ASUS Update utility ................................................ 4-14.1.2 Creating a bootable floppy disk .............................. 4-44.1.3 ASUS EZ Flash utility .............................................. 4-54.1.4 AFUDOS utility ........................................................ 4-64.1.5 ASUS CrashFree BIOS 2 utility ................................ 4-9

4.2 BIOS setup program ........................................................... 4-114.2.1 BIOS menu screen ................................................. 4-124.2.2 Menu bar ............................................................... 4-124.2.3 Navigation keys .................................................... 4-124.2.4 Menu items ........................................................... 4-134.2.5 Sub-menu items ................................................... 4-134.2.6 Configuration fields .............................................. 4-134.2.7 Pop-up window ..................................................... 4-134.2.8 Scroll bar .............................................................. 4-134.2.9 General help .......................................................... 4-13

4.3 Main menu .......................................................................... 4-144.3.1 System Time......................................................... 4-144.3.2 System Date ......................................................... 4-144.3.3 Legacy Diskette A ................................................ 4-144.3.4 Language .............................................................. 4-144.3.5 Primary, Secondary, Third,

and Fourth IDE Master/Slave ................................ 4-154.3.6 Storage Configuration .......................................... 4-164.3.7 System Information .............................................. 4-17

vvvvv

Contents4.4 Advanced menu .................................................................. 4-18

4.4.1 JumperFree Configuration .................................... 4-184.4.2 CPU Configuration ................................................. 4-224.4.3 Chipset Configuration ........................................... 4-274.4.4 Onboard Devices Configuration ............................ 4-304.4.5 PCI PnP ................................................................. 4-324.4.6 LAN Cable Status ................................................. 4-334.4.7 USB Configuration ................................................. 4-33

4.5 Power menu ........................................................................ 4-354.5.1 Suspend Mode ...................................................... 4-354.5.2 Repost Video on S3 Resume ................................ 4-354.5.3 ACPI 2.0 Support .................................................. 4-354.5.4 ACPI APIC Support ................................................ 4-354.5.5 APM Configuration ................................................ 4-364.5.6 Hardware Monitor ................................................. 4-38

4.6 Boot menu .......................................................................... 4-404.6.1 Boot Device Priority .............................................. 4-414.6.2 Boot Settings Configuration ................................. 4-424.6.3 Security ................................................................ 4-43

4.7 Exit menu ........................................................................... 4-45

Chapter 5:Chapter 5:Chapter 5:Chapter 5:Chapter 5: Software supportSoftware supportSoftware supportSoftware supportSoftware support5.1 Installing an operating system ............................................. 5-15.2 Support CD information ........................................................ 5-1

5.2.1 Running the support CD ......................................... 5-15.2.2 Drivers menu .......................................................... 5-25.2.3 Utilities menu .......................................................... 5-45.2.4 Make Disk menu ...................................................... 5-65.2.5 Manuals menu ......................................................... 5-75.2.6 ASUS Contact information ...................................... 5-85.2.7 Other information ................................................... 5-8

v iv iv iv iv i

Contents5.3 Software information ......................................................... 5-10

5.3.1 ASUS MyLogo2™ .................................................. 5-105.3.2 AI Net 2 ................................................................ 5-125.3.3 ASUS PC Probe II ................................................... 5-135.3.4 Cool ‘n’ Quiet™ Technology .................................. 5-195.3.5 Audio configuration .............................................. 5-21

5.4 RAID configurations ............................................................ 5-265.4.1 Installing hard disks .............................................. 5-275.4.2 ULI® RAID configurations ...................................... 5-275.4.3 Silicon Image® RAID configurations ....................... 5-35

5.5 Creating a RAID driver disk ................................................. 5-42

Chapter 6:Chapter 6:Chapter 6:Chapter 6:Chapter 6: ATI CrossFire™ technology supportATI CrossFire™ technology supportATI CrossFire™ technology supportATI CrossFire™ technology supportATI CrossFire™ technology support6.1 Overview............................................................................... 6-16.2 Hardware installation ............................................................ 6-26.3 Software information ........................................................... 6-5

6.3.1 Installing the device drivers .................................... 6-56.3.2 Using the Catalyst™ Control Center ....................... 6-7

v i iv i iv i iv i iv i i

Notices

Federal Communications Commission StatementFederal Communications Commission StatementFederal Communications Commission StatementFederal Communications Commission StatementFederal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions:• This device may not cause harmful interference, and• This device must accept any interference received including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance withmanufacturer’s instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications StatementCanadian Department of Communications StatementCanadian Department of Communications StatementCanadian Department of Communications StatementCanadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noiseemissions from digital apparatus set out in the Radio InterferenceRegulations of the Canadian Department of Communications.

This class B digital apparatus complies with CanadianThis class B digital apparatus complies with CanadianThis class B digital apparatus complies with CanadianThis class B digital apparatus complies with CanadianThis class B digital apparatus complies with CanadianICES-003.ICES-003.ICES-003.ICES-003.ICES-003.

The use of shielded cables for connection of the monitor to the graphicscard is required to assure compliance with FCC regulations. Changes ormodifications to this unit not expressly approved by the partyresponsible for compliance could void the user’s authority to operatethis equipment.

v i i iv i i iv i i iv i i iv i i i

Safety information

Electrical safetyElectrical safetyElectrical safetyElectrical safetyElectrical safety

• To prevent electrical shock hazard, disconnect the power cable fromthe electrical outlet before relocating the system.

• When adding or removing devices to or from the system, ensure thatthe power cables for the devices are unplugged before the signal cablesare connected. If possible, disconnect all power cables from the existingsystem before you add a device.

• Before connecting or removing signal cables from the motherboard,ensure that all power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord.These devices could interrupt the grounding circuit.

• Make sure that your power supply is set to the correct voltage in yourarea. If you are not sure about the voltage of the electrical outlet youare using, contact your local power company.

• If the power supply is broken, do not try to fix it by yourself. Contact aqualified service technician or your retailer.

Operation safetyOperation safetyOperation safetyOperation safetyOperation safety• Before installing the motherboard and adding devices on it, carefully read

all the manuals that came with the package.• Before using the product, make sure all cables are correctly connected

and the power cables are not damaged. If you detect any damage,contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away fromconnectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place theproduct in any area where it may become wet.

• Place the product on a stable surface.• If you encounter technical problems with the product, contact a qualified

service technician or your retailer.

The symbol of the crossed out wheeled bin indicates that the product(electrical and electronic equipment) should not be placed in municipalwaste. Please check local regulations for disposal of electronic products.

i xi xi xi xi x

About this guideThis user guide contains the information you need when installing andconfiguring the motherboard.

How this guide is organizedHow this guide is organizedHow this guide is organizedHow this guide is organizedHow this guide is organizedThis guide contains the following parts:

••••• Chapter 1: Product introduct ionChapter 1: Product introduct ionChapter 1: Product introduct ionChapter 1: Product introduct ionChapter 1: Product introduct ionThis chapter describes the features of the motherboard and the newtechnology it supports.

••••• Chapter 2: Hardware informat ionChapter 2: Hardware informat ionChapter 2: Hardware informat ionChapter 2: Hardware informat ionChapter 2: Hardware informat ionThis chapter lists the hardware setup procedures that you have toperform when installing system components. It includes description ofthe switches, jumpers, and connectors on the motherboard.

••••• Chapter 3: Power ing upChapter 3: Power ing upChapter 3: Power ing upChapter 3: Power ing upChapter 3: Power ing upThis chapter describes the power up sequence, the vocal POSTmessages, and ways of shutting down the system.

••••• Chapter 4: B IOS setupChapter 4: B IOS setupChapter 4: B IOS setupChapter 4: B IOS setupChapter 4: B IOS setupThis chapter tells how to change system settings through the BIOSSetup menus. Detailed descriptions of the BIOS parameters are alsoprovided.

••••• Chapter 5: Software supportChapter 5: Software supportChapter 5: Software supportChapter 5: Software supportChapter 5: Software supportThis chapter describes the contents of the support CD that comeswith the motherboard package.

••••• Chapter 6: ATI CrossF i reChapter 6: ATI CrossF i reChapter 6: ATI CrossF i reChapter 6: ATI CrossF i reChapter 6: ATI CrossF i re™™™™™ technology support technology support technology support technology support technology supportThis chapter tells how to install ATI CrossFire™ graphics cards.

Where to find more informationWhere to find more informationWhere to find more informationWhere to find more informationWhere to find more informationRefer to the following sources for additional information and for productand software updates.

1 .1 .1 .1 .1 . ASUS webs itesASUS webs itesASUS webs itesASUS webs itesASUS webs itesThe ASUS website provides updated information on ASUS hardwareand software products. Refer to the ASUS contact information.

2 .2 .2 .2 .2 . Opt ional documentat ionOpt ional documentat ionOpt ional documentat ionOpt ional documentat ionOpt ional documentat ionYour product package may include optional documentation, such aswarranty flyers, that may have been added by your dealer. Thesedocuments are not part of the standard package.

xxxxx

Conventions used in this guideConventions used in this guideConventions used in this guideConventions used in this guideConventions used in this guideTo make sure that you perform certain tasks properly, take note of thefollowing symbols used throughout this manual.

DANGER/WARNING: DANGER/WARNING: DANGER/WARNING: DANGER/WARNING: DANGER/WARNING: Information to prevent injury to yourselfwhen trying to complete a task.

CAUTION:CAUTION:CAUTION:CAUTION:CAUTION: Information to prevent damage to the componentswhen trying to complete a task.

NOTE: NOTE: NOTE: NOTE: NOTE: Tips and additional information to help you complete atask.

IMPORTANT: IMPORTANT: IMPORTANT: IMPORTANT: IMPORTANT: Instructions that you MUST follow to complete atask.

TypographyTypographyTypographyTypographyTypographyBo l d t e x tBo l d t e x tBo l d t e x tBo l d t e x tBo l d t e x t Indicates a menu or an item to select.Italics Used to emphasize a word or a phrase.<Key> Keys enclosed in the less-than and greater-than sign means

that you must press the enclosed key.

Example: <Enter> means that you must press the Enter orReturn key.

<Key1+Key2+Key3> If you must press two or more keys simultaneously, thekey names are linked with a plus sign (+).

Example: <Ctrl+Alt+D>

Command Means that you must type the command exactly as shown,then supply the required item or value enclosed inbrackets.

Example: At the DOS prompt, type the command line:afudos /i[filename]afudos /iA8R32-MVP.ROM

x ix ix ix ix i

A8R32-MVP Deluxe specifications summary

C P UC P UC P UC P UC P U

Ch ipsetCh ipsetCh ipsetCh ipsetCh ipset

System busSystem busSystem busSystem busSystem bus

MemoryMemoryMemoryMemoryMemory

Expans ion s lotsExpans ion s lotsExpans ion s lotsExpans ion s lotsExpans ion s lots

CrossF i re™CrossF i re™CrossF i re™CrossF i re™CrossF i re™

Sto rageSto rageSto rageSto rageSto rage

H igh Def in i t ionH igh Def in i t ionH igh Def in i t ionH igh Def in i t ionH igh Def in i t ionAud i oAud i oAud i oAud i oAud i o

L A NL A NL A NL A NL A N

IEEE 1394aIEEE 1394aIEEE 1394aIEEE 1394aIEEE 1394a

U S BU S BU S BU S BU S B

B IOS featuresB IOS featuresB IOS featuresB IOS featuresB IOS features

(continued on the next page)

Socket 939 for AMD Athlon™ 64FX/Athlon™ 64 X2/Athlon™ 64/Opteron processor

AMD64 architecture enables simultaneous 32- and64-bit computing

Supports AMD Cool ‘n’ Quiet™ TechnologySupports AMD HyperTransport™ Technology

ATI CrossFire™ Xpress 3200/ULi M1575

2000/1600 MT/s

Dual-channel memory architecture4 x 184-pin DIMM sockets support up to 4 GB

unbufferred ECC/non-ECC 400/333/266 MHz DDRmemory modules

2 x PCI Express™ x16 slots with CrossFire support at fullx16, x16 mode

1 x PCI Express™ x1 slot3 x PCI slots

Supports ATI CrossFire™ graphics cards (both at x16mode)

ULi M1575 Southbridge supports:- 2 x IDE connectors for up to four Ultra DMA

133/100/66/33 hard disks- 4 x Serial ATA I/II 3.0 Gb/s hard disks with RAID 0,

RAID 1, RAID 0+1, RAID 5, and JBOD configurationSilicon Image® 3132 SATA controller supports:- 1 x Internal Serial ATA 3 Gb/s hard disk- 1 x External Serial ATA hard disk (SATA On-the-Go)- RAID 0 and RAID 1 configuration

Realtek® ALC882 8-channel High Definition Audio (HDAudio) CODEC

Supports Multi-streaming and Universal Audio JackCoaxial / Optical S/PDIF Out ports on the rear panel

Marvell® 88E8001 Gigabit LAN controller, featuringAI NET2

Marvell® 88E8053 PCIe Gigabit LAN Controller, featuring AINET2

T1 1394a controller supports:- 2 x IEEE 1394a connectors at mid-board

Supports up to 8 USB 2.0/1.1 ports

8 Mb Flash ROM, AMI BIOS, PnP, DMI2.0, SM BIOS 2.3,WfM2.0

x i ix i ix i ix i ix i i

Stack Cool 2ASUS SATA On-the-Go (External Serial ATA port on the

rear panel)

ASUS MyLogo2™ASUS Multi-language BIOSASUS CrashFree BIOS 2ASUS AI NET 2ASUS Q-Fan2 TechnologyASUS EZ Flash

Intelligent overclocking tools:- AI NOS™ (Non-delay Overclocking System)- AI Overclocking (intelligent CPU frequency tuner)- ASUS PEG Link (automatic performance tuning for

single/dual graphics cards)Precision Tweaker supports:

- DIMM voltage: 12-step DRAM voltage control- Core voltage: Adjustable CPU voltage at 0.025 V

increment- Northbridge voltage: Adjustable voltage at 0.1 V

increment for core power, HT bus, and PCI Expressbus

Stepless Frequency Selection(SFS) allows:- FSB tuning from 200 MHz to 400 MHz at 1 MHz increment- PCI Express frequency tuning from 100 MHz to

150 MHz at 1 MHz incrementOverclocking protection:

- ASUS C.P.R. (CPU Parameter Recall)

1 x PS/2 mouse port1 x PS/2 keyboard port1 x Parallel port2 x LAN (RJ-45) ports4 x USB 2.0/1.1 ports1 x Coaxial S/PDIF Out port1 x Optical S/PDIF Out port1 x External Serial ATA port8-Channel audio ports

WfM 2.0, DMI 2.0, WOL by PME, WOR by PME, chassisintrusion, PXE, and RPL

1 x Floppy disk drive connector2 x IDE connectors1 x CPU fan connector2 x Chassis fan connector1 x Power fan connector2 x IEEE 1394a connectors5 x Serial ATA connectors

A8R32-MVP Deluxe specifications summary

ASUS A I L i feASUS A I L i feASUS A I L i feASUS A I L i feASUS A I L i fefeatu resfeatu resfeatu resfeatu resfeatu res

Other ASUSOther ASUSOther ASUSOther ASUSOther ASUSspec ia l featuresspec ia l featuresspec ia l featuresspec ia l featuresspec ia l features

Overc lock ingOverc lock ingOverc lock ingOverc lock ingOverc lock ing

Rear pane lRear pane lRear pane lRear pane lRear pane l

Manageab i i tyManageab i i tyManageab i i tyManageab i i tyManageab i i ty

I n te rna lI n te rna lI n te rna lI n te rna lI n te rna lconnectorsconnectorsconnectorsconnectorsconnectors

(continued on the next page)

x i i ix i i ix i i ix i i ix i i i

2 x USB 2.0 connectors for four additional USB 2.0ports

1 x 24-pin EATX power connector1 x 4-pin ATX 12 V power connector1 x GAME/MIDI connector1 x CD-in connector1 x COM connector1 x Chassis intrusion connector1 x Front panel High Definition Audio connector1 x System panel connector

DriversASUS PC Probe IIASUS UpdateAnti-virus software (OEM version)

ATX form factor: 12 in x 9.6 in (30.5 cm x 24.4 cm)

In te rna lI n te rna lI n te rna lI n te rna lI n te rna lconnectorsconnectorsconnectorsconnectorsconnectors

Support CDSupport CDSupport CDSupport CDSupport CDcontentscontentscontentscontentscontents

Form factorForm factorForm factorForm factorForm factor

*Specifications are subject to change without notice.

A8R32-MVP Deluxe specifications summary

x i vx i vx i vx i vx i v

1Productinformation

This chapter describes themotherboard features and the newtechnologies it supports

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE

Chapter summary 11.1 Welcome! .............................................................................. 1-11.2 Package contents ................................................................. 1-11.3 Special features .................................................................... 1-2

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 1 - 11 - 11 - 11 - 11 - 1

1.1 Welcome!Thank you for buying an ASUSThank you for buying an ASUSThank you for buying an ASUSThank you for buying an ASUSThank you for buying an ASUS®®®®® A8R32-MVP Deluxe A8R32-MVP Deluxe A8R32-MVP Deluxe A8R32-MVP Deluxe A8R32-MVP Deluxemotherboard!motherboard!motherboard!motherboard!motherboard!

The motherboard delivers a host of new features and latest technologies,making it another standout in the long line of ASUS quality motherboards!

Before you start installing the motherboard, and hardware devices on it,check the items in your package with the list below.

1.2 Package contentsCheck your motherboard package for the following items.

MotherboardMotherboardMotherboardMotherboardMotherboard ASUS A8R32-MVP Deluxe motherboard

Cab lesCab lesCab lesCab lesCab les 1 x Floppy disk drive signal cable1 x IDE cable1 x Ultra DMA cable 133/100/66 cable5 x Serial ATA cables1 x 1-port Serial ATA power cable2 x 2-port Serial ATA power cables1 x 2-port IEEE 1394a cable

Accessor iesAccessor iesAccessor iesAccessor iesAccessor ies 1 x COM port moduleI/O shield1 x 2-port USB 2.0/Game module

Appl icat ion CDsAppl icat ion CDsAppl icat ion CDsAppl icat ion CDsAppl icat ion CDs ASUS motherboard support CD

Documentat ionDocumentat ionDocumentat ionDocumentat ionDocumentat ion User guide

If any of the above items is damaged or missing, contact your retailer.

1 - 21 - 21 - 21 - 21 - 2 Chapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ion

1.3 Special features

1.3.11.3.11.3.11.3.11.3.1 Product highlightsProduct highlightsProduct highlightsProduct highlightsProduct highlights

Latest processor technology Latest processor technology Latest processor technology Latest processor technology Latest processor technology

The motherboard comes with a 939-pin surface mount, Zero InsertionForce (ZIF) socket that supports AMD Athlon™ 64/Athlon™ 64 FX/Athlon™64 X2 processors. With an integrated low-latency high-bandwidth memorycontroller and a highly-scalable HyperTransport™ technology-based systembus, the motherboard provides a powerful platform for your diversecomputing needs, increased office productivity, and enhanced digital mediaexperience. See page 2-6.

ATI CrossFire™ Xpress 3200 ATI CrossFire™ Xpress 3200 ATI CrossFire™ Xpress 3200 ATI CrossFire™ Xpress 3200 ATI CrossFire™ Xpress 3200 The motherboard features ATI CrossFire™ Xpress 3200 support, deliveringimproved overclocking and optimal PCI Express device performance. Thecombined multi-GPU power boosts image quality and rendering speed forthe highest quality images. With its optimized peer-to-peer and general linkperformance GPU sharing, you are a step ahead in graphics and gamingeffects. The chipset allows higher antialiasing, anisotropic filtering, sharing,and texture settings. The ATI CrossFire™ Xpress 3200 also comes with theATI Catalyst™ Control Center that allows you to get real-time 3D-renderedpreviews of adjustments to your display configurations and advanced 3Dsettings.

PCI Express™ interface PCI Express™ interface PCI Express™ interface PCI Express™ interface PCI Express™ interface The motherboard fully supports PCI Express, the latest I/O interconnecttechnology that speeds up the PCI bus. PCI Express features point-to-pointserial interconnections between devices and allows higher clockspeeds bycarrying data in packets. This high speed interface is software compatiblewith existing PCI specifications. See page 2-17 for details.

Serial ATA 3Gb/s technology Serial ATA 3Gb/s technology Serial ATA 3Gb/s technology Serial ATA 3Gb/s technology Serial ATA 3Gb/s technology The motherboard supports the Serial ATA II 3 Gb/s technology through theSerial ATA interfaces and the ULI M1575 Southbridge. The Serial ATA II 3Gb/s specification provides twice the bandwidth of the current Serial ATAproducts with a host of new features, including Native Command Queueing(NCQ), and Power Management (PM) Implementation Algorithm. Serial ATAallows for thinner, more flexible cables with lower pin count, reduced voltagerequirement. See page 2-23 for details.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 1 - 31 - 31 - 31 - 31 - 3

Dual RAID solution Dual RAID solution Dual RAID solution Dual RAID solution Dual RAID solution Onboard RAID controllers provide the motherboard with dual-RAIDfunctionality that allows you to select the best RAID solution using SerialATA devices.

The ULi M1575 Southbridge allows RAID 0, RAID 1, RAID 0+1, and JBODconfiguration for four SATA 3Gb/s. See page 2-23 for details.

The Silicon Image® 3132 controller supports two additional Serial ATA3Gb/s connectors and allows RAID 0 and RAID 1 configurations through theinternal and external Serial ATA ports. See page 2-25 for details.

8-channel high definition audio 8-channel high definition audio 8-channel high definition audio 8-channel high definition audio 8-channel high definition audio Onboard is the Realtek® ALC882 High Definition Audio 8-channel audioCODEC. This CODEC is fully-compliant with Intel® High Definition Audiostandard (192 KHz, 24-bit audio). With the CODEC, 8-channel audio ports,and S/PDIF interfaces, you can connect your computer to home theaterdecoders to produce crystal-clear digital audio.

The Realtek® ALC882 CODEC comes with a software application thatfeatures jack detection to monitor the plugging status of each jack,impedance sensing to determine audio device classes, and pre-definedequalization for various audio devices. See page 2-20 for details.

Dual Gigabit LAN solution Dual Gigabit LAN solution Dual Gigabit LAN solution Dual Gigabit LAN solution Dual Gigabit LAN solution The motherboard comes with dual Gigabit LAN controllers to provide the totalsolution for your networking needs. These network controllers use both PCIExpress and PCI segments to provide faster data bandwidth for your wired orwireless Internet, LAN, and file sharing requirements. See page 2-21 fordetails.

IEEE 1394a support IEEE 1394a support IEEE 1394a support IEEE 1394a support IEEE 1394a support

The IEEE 1394a interface provides high-speed and flexible PC connectivityto a wide range of peripherals and devices compliant to IEEE 1394astandards. The IEEE 1394a interface allows up to 400 Mbps transfer ratesthrough simple, low-cost, high-bandwidth asynchronous (real-time) datainterfacing between computers, peripherals, and consumer electronicdevices such as camcorders, VCRs, printers,TVs, and digital cameras. Seepage 2-29 for details.

1 - 41 - 41 - 41 - 41 - 4 Chapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ion

USB 2.0 technology USB 2.0 technology USB 2.0 technology USB 2.0 technology USB 2.0 technology

The motherboard implements the Universal Serial Bus (USB) 2.0specification, dramatically increasing the connection speed from the12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 isbackward compatible with USB 1.1. See pages 2-21 and 2-27 for details.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 1 - 51 - 51 - 51 - 51 - 5

1.3.21.3.21.3.21.3.21.3.2 Innovative ASUS featuresInnovative ASUS featuresInnovative ASUS featuresInnovative ASUS featuresInnovative ASUS features

Fanless Design Fanless Design Fanless Design Fanless Design Fanless Design

The ASUS fanless design allows multi-directional heat flow from majorthermal sources in the motherboard to lower overall system temperature,resulting in quieter operation and longer system life.

Stack Cool 2 Stack Cool 2 Stack Cool 2 Stack Cool 2 Stack Cool 2

The motherboard comes with the ASUS Stack Cool 2, an innovative fan-lessand zero-noise thermal solution that provides supplementary cooling to themotherboard. Stack Cool 2 is a special layer underneath the motherboardthat improves heat dissipation.

SATA-On-the-Go SATA-On-the-Go SATA-On-the-Go SATA-On-the-Go SATA-On-the-Go

Leveraging the Serial ATA II feature is the SATA-On-the-Go. This externalport on the rear panel I/O provides smart setup, hot-plug and support forup to 16 devices with port-multiplier functions. See pages 2-21 for details.

AI NET2 AI NET2 AI NET2 AI NET2 AI NET2

The AI NET2 is a BIOS-based diagnostic tool that detects and reportsEthernet cable faults and shorts. With this utility, you can easily monitorthe condition of the Ethernet cable(s) connected to the LAN (RJ-45)port(s). During the bootup process, AI NET2 immediately diagnoses theLAN cable(s) and reports shorts and faults up to 100 meters at 1 meteraccuracy. See page 5-12 for details.

Precision TweakerPrecision TweakerPrecision TweakerPrecision TweakerPrecision TweakerThis feature allows you to fine tune the CPU/memory/Northbridge voltageand gradually increase the memory Front Side Bus (FSB) and PCI Expressfrequency at 1MHz increment to achieve maximum system performance.See pages 4-19 and 4-20 for details.

AI NOS™ (Non-Delay Overclocking System) AI NOS™ (Non-Delay Overclocking System) AI NOS™ (Non-Delay Overclocking System) AI NOS™ (Non-Delay Overclocking System) AI NOS™ (Non-Delay Overclocking System)

ASUS Non-delay Overclocking System™ (NOS) is a technology thatauto-detects the CPU loading and dynamically overclocks the CPU speedonly when needed. See page 4-19 for details.

1 - 61 - 61 - 61 - 61 - 6 Chapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ionChapter 1 : Product int roduct ion

PEG Link Mode for two graphics cards PEG Link Mode for two graphics cards PEG Link Mode for two graphics cards PEG Link Mode for two graphics cards PEG Link Mode for two graphics cards This feature enhances your PCI Express graphics card performance, allowingthe motherboard to automatically adjust the PCI Express graphics link modeto the correct frequency based on the system configuration. Fouradditional settings are available for overclocking the PEG Link Mode. Seepage 4-20 for details.

ASUS Q-Fan 2 technology ASUS Q-Fan 2 technology ASUS Q-Fan 2 technology ASUS Q-Fan 2 technology ASUS Q-Fan 2 technology The ASUS Q-Fan 2 technology smartly adjusts the CPU and chassis fansspeed according to the system loading to ensure quiet, cool, and efficientoperation. See page 4-39 for details.

ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 ASUS CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CDwhen the BIOS codes and data are corrupted. This protection eliminates theneed to buy a replacement ROM chip. See page 4-9 for details.

ASUS Multi-language BIOS ASUS Multi-language BIOS ASUS Multi-language BIOS ASUS Multi-language BIOS ASUS Multi-language BIOS The multi-language BIOS allows you to select the language of your choicefrom the available options. The localized BIOS menus allow easier and fasterconfiguration. See page 4-14 for details.

ASUS MyLogo2™ ASUS MyLogo2™ ASUS MyLogo2™ ASUS MyLogo2™ ASUS MyLogo2™ This new feature present in the motherboard allows you to personalize andadd style to your system with customizable boot logos. See page 4-42 fordetails.

C.P.R. (CPU Parameter Recall) C.P.R. (CPU Parameter Recall) C.P.R. (CPU Parameter Recall) C.P.R. (CPU Parameter Recall) C.P.R. (CPU Parameter Recall)

The C.P.R. feature of the motherboard BIOS allows automatic re-setting tothe BIOS default settings in case the system hangs due to overclocking.When the system hangs due to overclocking, C.P.R. eliminates the need toopen the system chassis and clear the RTC data. Simply shut down andreboot the system, and the BIOS automatically restores the CPU defaultsetting for each parameter. See page 2-19 for details.

ASUS EZ Flash BIOS ASUS EZ Flash BIOS ASUS EZ Flash BIOS ASUS EZ Flash BIOS ASUS EZ Flash BIOS With the ASUS EZ Flash, you can easily update the system BIOS evenbefore loading the operating system. No need to use a DOS-based utility orboot from a floppy disk. See page 4-5 for details.

2Hardwareinformation

This chapter lists the hardware setupprocedures that you have to performwhen installing system components.It includes description of the jumpersand connectors on the motherboard.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE

Chapter summary 22.1 Before you proceed .............................................................. 2-12.2 Motherboard overview .......................................................... 2-22.3 Central Processing Unit (CPU) .............................................. 2-62.4 System memory ................................................................. 2-112.5 Expansion slots ................................................................... 2-152.6 Jumper ............................................................................... 2-192.7 Connectors ......................................................................... 2-20

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 - 12 - 12 - 12 - 12 - 1

Onboard LEDOnboard LEDOnboard LEDOnboard LEDOnboard LEDThe motherboard comes with a standby power LED that lights up toindicate that the system is ON, in sleep mode, or in soft-off mode.This is a reminder that you should shut down the system and unplugthe power cable before removing or plugging in any motherboardcomponent. The illustration below shows the location of the onboardLED.

2.1 Before you proceedTake note of the following precautions before you install motherboardcomponents or change any motherboard settings.

• Unplug the power cord from the wall socket before touching anycomponent.

• Use a grounded wrist strap or touch a safely grounded object or ametal object, such as the power supply case, before handlingcomponents to avoid damaging them due to static electricity

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a groundedantistatic pad or in the bag that came with the component.

• Before you insta l l o r remove any component , ensureBefore you insta l l o r remove any component , ensureBefore you insta l l o r remove any component , ensureBefore you insta l l o r remove any component , ensureBefore you insta l l o r remove any component , ensurethat the ATX power supp ly i s sw itched of f or thethat the ATX power supp ly i s sw itched of f or thethat the ATX power supp ly i s sw itched of f or thethat the ATX power supp ly i s sw itched of f or thethat the ATX power supp ly i s sw itched of f or thepower cord i s detached f rom the power supp ly . power cord i s detached f rom the power supp ly . power cord i s detached f rom the power supp ly . power cord i s detached f rom the power supp ly . power cord i s detached f rom the power supp ly . Failureto do so may cause severe damage to the motherboard, peripherals,and/or components.

Make sure to connect the EZPlug when using two PCI Express graphicscards and a 20-pin ATX power supply unit, or if the graphics cards donot have auxiliary power plugs. See page 2-26 for the location of theEZPlug connector.

A8R32-MVP DELUXE

A8R32-MVP DELUXE Onboard LED

SB_PWR

ONStandbyPower

OFFPowered

Off

2 - 22 - 22 - 22 - 22 - 2 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

A8R32-MVP DELUXE

2.2 Motherboard overviewBefore you install the motherboard, study the configuration of your chassisto ensure that the motherboard fits into it. Refer to the chassisdocumentation before installing the motherboard.

Make sure to unplug the power cord before installing or removing themotherboard. Failure to do so can cause you physical injury and damagemotherboard components.

2.2.12.2.12.2.12.2.12.2.1 Placement directionPlacement directionPlacement directionPlacement directionPlacement directionWhen installing the motherboard, make sure that you place it into thechassis in the correct orientation. The edge with external ports goes to therear part of the chassis as indicated in the image below.

2.2.22.2.22.2.22.2.22.2.2 Screw holesScrew holesScrew holesScrew holesScrew holesPlace nine (9) screws into the holes indicated by circles to secure themotherboard to the chassis.

Do not overtighten the screws! Doing so can damage the motherboard.

P l ace th i s s i de towa rdsP l ace th i s s i de towa rdsP l ace th i s s i de towa rdsP l ace th i s s i de towa rdsP l ace th i s s i de towa rdsthe r ea r o f the chass i sthe r ea r o f the chass i sthe r ea r o f the chass i sthe r ea r o f the chass i sthe r ea r o f the chass i s

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 - 32 - 32 - 32 - 32 - 3

2.2.32.2.32.2.32.2.32.2.3 Motherboard layoutMotherboard layoutMotherboard layoutMotherboard layoutMotherboard layout

PANEL

A8R32-MVP DELUXE

AAFP

GAMECHASSIS

C_I

24.5cm (9.6in)

30.5

cm (

12.0

in)

CPU_FAN

R D

IMM

_B1

(64

bit,1

84-p

in m

odul

R D

IMM

_A1

(64

bit,1

84-p

in m

odul

R D

IMM

_A2

(64

bit,1

84-p

in m

odul

R D

IMM

_B2

(64

bit,1

84-p

in m

odul

PWR_FAN

LAN1_USB12

IE1394_1

CHA_FAN2S

uper

I/O8MbBIOS

TSB43AB22A

PS/2KBMST: MouseB: Keyboard

PAR

L P

SPDIF_O

SPDIF_O2

LAN2_USB34

ACL882

PCIEX16_1

PCI1

PCI2

Marvell88E8001

CLRTC

USB56

SATA4SATA3

SATA_RAID2

ATA

ULIM1575

SB_PWR

EAT

I_ID

CR2032 3VLithium Cell

CMOS Power

CHA_FAN1

AUDIO

Marvell88E8053

COM1

ATX12V

PCIEX1_1

IE1394_2

USB78_WFG

Soc

ket 9

PCI3

ATI™CrossFire™Xpress 3200

PCIEX16_2

SATA2SATA1

FLO

2 - 42 - 42 - 42 - 42 - 4 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.2.42.2.42.2.42.2.42.2.4 Layout ContentsLayout ContentsLayout ContentsLayout ContentsLayout Contents

S l o t sS l o t sS l o t sS l o t sS l o t s P a g eP a g eP a g eP a g eP a g e1. DDR DIMM slots 2-112. PCI slots 2-173. PCI Express x1 slot 2-174. PCI Express x16 slots 2-17

J u m p e rJ u m p e rJ u m p e rJ u m p e rJ u m p e r P a g eP a g eP a g eP a g eP a g e1. Clear RTC RAM (3-pin CLRTC) 2-19

Rea r pane l connec to r sRea r pane l connec to r sRea r pane l connec to r sRea r pane l connec to r sRea r pane l connec to r s P a g eP a g eP a g eP a g eP a g e1. PS/2 mouse port 2-202. Parallel port 2-203. Side Speaker Out port 2-204. Center/Subwoofer port 2-205. Line In port 2-206. Line Out port 2-207. LAN 1 (RJ-45) 2-218. LAN 2 (RJ-45) 2-219. USB 2.0 ports 3 and 4 2-2110. USB 2.0 ports 1 and 2 2-2111. Microphone port 2-2112. Rear Speaker Out port 2-2113. External SATA port 2-2114. Optical S/PDIF Out port 2-2115. Coaxial S/PDIF Out port 2-2116. PS/2 keyboard port 2-21

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 - 52 - 52 - 52 - 52 - 5

In te rna l connec to r sI n te rna l connec to r sI n te rna l connec to r sI n te rna l connec to r sI n te rna l connec to r s P a g eP a g eP a g eP a g eP a g e1. Floppy disk drive connector (34-1 pin FLOPPY) 2-222. IDE connectors (40-1 pin PRI_IDE, 40-1 pin SEC_IDE) 2-223. Serial ATA connectors (7-pin SATA1 [red], SATA2 [red],

SATA3 [black], SATA4 [black]) 2-234. Silicon Image Serial ATA RAID connector (7-pin SATA_RAID 2) 2-255. CPU, Chassis, and Power fan connectors 2-26

(3-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin PWR_FAN )6. USB connectors (10-1 USB56, USB78_WFG) 2-277. Power connectors (24-pin EATXPWR, 4-pin ATX12V) 2-278. GAME/MIDI port connector (16-1 pin GAME) 2-289. Serial port connector (10-1 pin COM1) 2-2910. IEEE 1394a connectors (10-1 pin IE1394_1; 10-1 pin IE1394_2) 2-2911. Chassis intrusion connector (4-1 pin CHASSIS) 2-3012. Front panel audio connector (10-1 pin AAFP) 2-3113. Audio connector (4-pin CD [black]) 2-3114. System panel connectors (20-1 pin PANEL) 2-32

- System Power LED (Green 3-pin PLED)- Hard Disk activity (Red 2-pin IDE_LED)- System warning speaker (Orange 4-pin SPEAKER)- Power/Soft-off button(Yellow 2-pin PWRSW)- Reset switch (Blue 2-pin RESET)

2 - 62 - 62 - 62 - 62 - 6 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.3 Central Processing Unit (CPU)The motherboard comes with a surface mount 939-pin Zero Insertion Force(ZIF) socket designed for the AMD Athlon™ 64FX/AMD Athlon™ 64 /Athlon™ 64 X2/Opteron processor.

The 128-bit-wide data paths of these processors can run applicationsfaster than processors with only 32-bit or 64-bit wide data paths.

Take note of the marked corner (with goldtriangle) on the CPU. This mark should matcha specific corner on the socket to ensurecorrect installation.

2.3.12.3.12.3.12.3.12.3.1 Installing the CPUInstalling the CPUInstalling the CPUInstalling the CPUInstalling the CPUTo install a CPU.

1. Locate the 939-pin ZIF socket on the motherboard.

2. Unlock the socket by pressingthe lever sideways, then lift it upto a 90°-100° angle.

Make sure that the socket lever is lifted up to 90°-100° angle, otherwisethe CPU does not fit in completely.

Socke t l e ve rSocke t l e ve rSocke t l e ve rSocke t l e ve rSocke t l e ve r

A8R32-MVP DELUXE

A8R32-MVP DELUXE CPU Socket 939

G o l dG o l dG o l dG o l dG o l dt r i a ng l et r i a ng l et r i a ng l et r i a ng l et r i a ng l e

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 - 72 - 72 - 72 - 72 - 7

3. Position the CPU above thesocket such that the CPU cornerwith the gold triangle matchesthe socket corner with a smalltriangle.

4. Carefully insert the CPU into thesocket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU intothe socket to prevent bending the pins and damaging the CPU!

5. When the CPU is in place, pushdown the socket lever to securethe CPU. The lever clicks on theside tab to indicate that it islocked.

6. Install a CPU heatsink and fanfollowing the instructions thatcame with the heatsink package.

Go l d t r i a ng l eGo l d t r i a ng l eGo l d t r i a ng l eGo l d t r i a ng l eGo l d t r i a ng l e

Sma l l t r i a ng l eSma l l t r i a ng l eSma l l t r i a ng l eSma l l t r i a ng l eSma l l t r i a ng l e

2 - 82 - 82 - 82 - 82 - 8 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.3.22.3.22.3.22.3.22.3.2 Installing the heatsink and fanInstalling the heatsink and fanInstalling the heatsink and fanInstalling the heatsink and fanInstalling the heatsink and fanThe AMD Athlon™ 64FX/Athlon™ 64/Athlon™ 64 X2 processor requires aspecially designed heatsink and fan assembly to ensure optimum thermalcondition and performance.

Make sure that you use only AMD-certified heatsink and fan assembly.

To install the CPU heatsink and fan:

1. Place the heatsink on top of the installed CPU, making sure that theheatsink fits properly on the retention module base.

• The retention module base is already installed on the motherboardupon purchase.

• You do not have to remove the retention module base wheninstalling the CPU or installing other motherboard components.

• If you purchased a separate CPU heatsink and fan assembly, makesure that a Thermal Interface Material is properly applied to the CPUheatsink or CPU before you install the heatsink and fan assembly.

Re tent i on modu l e baseRetent i on modu l e baseRetent i on modu l e baseRetent i on modu l e baseRetent i on modu l e base

CPU hea t s i n kCPU hea t s i n kCPU hea t s i n kCPU hea t s i n kCPU hea t s i n k

C P U f a nC P U f a nC P U f a nC P U f a nC P U f a n

Retent i on b racke t l ockRetent i on b racke t l ockRetent i on b racke t l ockRetent i on b racke t l ockRetent i on b racke t l ock

Reten t i on b r acke tRe ten t i on b r acke tRe ten t i on b r acke tRe ten t i on b r acke tRe ten t i on b r acke t

Your boxed CPU heatsink and fan assembly should come with installationinstructions for the CPU, heatsink, and the retention mechanism. If theinstructions in this section do not match the CPU documentation, followthe latter.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 - 92 - 92 - 92 - 92 - 9

2. Attach one end of the retentionbracket to the retention modulebase.

3. Align the other end of theretention bracket (near theretention bracket lock) to theretention module base. A clickingsound denotes that the retentionbracket is in place.

Make sure that the fan andheatsink assembly perfectly fitsthe retention mechanism modulebase, otherwise you cannot snapthe retention bracket in place.

4. Push down the retention bracketlock on the retention mechanismto secure the heatsink and fan tothe module base.

2 -102 -102 -102 -102 -10 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

5. When the fan and heatsink assembly is in place, connect the CPU fancable to the connector on the motherboard labeled CPU_FAN.

Do not forget to connect the CPU fan connector! Hardware monitoringerrors can occur if you fail to plug this connector.

A8R32-MVP DELUXE

A8R32-MVP DELUXE CPU fan connector

CPU_FAN

Rot

atio

12V

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 -112 -112 -112 -112 -11

2.4 System memory

2.4.12.4.12.4.12.4.12.4.1 OverviewOverviewOverviewOverviewOverviewThe motherboard comes with four 184-pin Double Data Rate (DDR) DualInline Memory Modules (DIMM) sockets.

The following figure illustrates the location of the sockets:

Channe lChanne lChanne lChanne lChanne l S o c k e t sS o c k e t sS o c k e t sS o c k e t sS o c k e t sChannel A DIMM_A1 and DIMM_A2Channel B DIMM_B1 and DIMM_B2

In dual-channel configurations, installing ident i ca l i dent i ca l i dent i ca l i dent i ca l i dent i ca l (the same type andsize) DDR DIMM pairs for each channel provides optimum performance.

A8R32-MVP DELUXE

A8R32-MVP DELUXE 184-pin DDR DIMM sockets

DIM

M_A

DIM

M_A

DIM

M_B

DIM

M_B

2 -122 -122 -122 -122 -12 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.4.22.4.22.4.22.4.22.4.2 Memory ConfigurationsMemory ConfigurationsMemory ConfigurationsMemory ConfigurationsMemory ConfigurationsYou may install 256 MB, 512 MB, and 1 GB unbuffered ECC/non-ECC DDRDIMMs into the DIMM sockets using the memory configurations in thissection.

• If you installed four 1 GB memory modules, the system may detectless than 3 GB of total memory because of address space allocationfor other critical functions. This limitation applies to Windows® XP32-bit version operating system since it does not support PhysicalAddress Extension (PAE).

• When using only one DDR DIMM module, install it into slot DIMM_B1only.

• For single-channel memory configuration, start installing the DDRDIMMs from slot DIMM_B1 or DMM_B2.

• For dual-channel memory configuration, install the DIMMs in slotsDIMM_B1 and DIMM_A1 (blue slots); install another pair of DIMMs inslots DIMM_B2 and DIMM_A2 (black slots).

• Always install DIMMs with the same CAS latency. For optimumresults, we recommend that you obtain memory modules from thesame vendor. Refer to the Qualified Vendors List on the next pagefor details.

• When you install four double-sided 400 MHz DDR DIMMs, thefrequency of each module downgrades to 333 MHz.

Recommended memory configurationsRecommended memory configurationsRecommended memory configurationsRecommended memory configurationsRecommended memory configurations

S o c k e t sS o c k e t sS o c k e t sS o c k e t sS o c k e t sM o d eM o d eM o d eM o d eM o d e D IMM_A1D IMM_A1D IMM_A1D IMM_A1D IMM_A1 D IMM_A2D IMM_A2D IMM_A2D IMM_A2D IMM_A2 D I M M _ B 1D I M M _ B 1D I M M _ B 1D I M M _ B 1D I M M _ B 1 D I M M _ B 2D I M M _ B 2D I M M _ B 2D I M M _ B 2D I M M _ B 2Single-channel (1) – – Populated –Dual-channel* (1) Populated – Populated –

(2) Populated Populated Populated Populated

* Use on l y i dent i ca l DDR D IMM pa i r s .* Use on l y i dent i ca l DDR D IMM pa i r s .* Use on l y i dent i ca l DDR D IMM pa i r s .* Use on l y i dent i ca l DDR D IMM pa i r s .* Use on l y i dent i ca l DDR D IMM pa i r s .* Fo r dua l - channe l con f i gu ra t i on (2) , you may :* Fo r dua l - channe l con f i gu ra t i on (2) , you may :* Fo r dua l - channe l con f i gu ra t i on (2) , you may :* Fo r dua l - channe l con f i gu ra t i on (2) , you may :* Fo r dua l - channe l con f i gu ra t i on (2) , you may :

• install identical DIMMs in all four socketsO RO RO RO RO R

• install identical DIMM pair in DIMM_A1 and DIMM_B1 (blue sockets)

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 -132 -132 -132 -132 -13

DDR (400 MHz) Qualified Vendors ListDDR (400 MHz) Qualified Vendors ListDDR (400 MHz) Qualified Vendors ListDDR (400 MHz) Qualified Vendors ListDDR (400 MHz) Qualified Vendors List

S i z eS i z eS i z eS i z eS i z e V e n d o rV e n d o rV e n d o rV e n d o rV e n d o r C h i p N o .C h i p N o .C h i p N o .C h i p N o .C h i p N o . B r a n dB r a n dB r a n dB r a n dB r a n d S i d e / s *S i d e / s *S i d e / s *S i d e / s *S i d e / s * P a r t N o .P a r t N o .P a r t N o .P a r t N o .P a r t N o . AAAAA BBBBB CCCCC

256 MB KINGSTON V58C2256804SAT5(ECC) – SS KVR400X72C3A/256 • • •512 MB KINGSTON V58C2256804SAT5(ECC) – DS KVR400X72C3A/512 • • •512 MB KINGSTON Heat-Sink Package – DS KHX3200A/512 • • •256 MB KINGSTON D3208DL3T-5A – SS KVR400X64C3A/256 • • •256 MB KINGSTON A2S56D30BTP – SS KVR400X64C3A/256 • • •512 MB KINGSTON HY5DU12822BT-D43 – SS KVR400X64C3A/512 • • •512 MB SAMSUNG K4H560838E-TCCC(ECC) SAMSUNG DS M381L6423ETM-CCC • • •512 MB SAMSUNG K4H560838F-TCCC SAMSUNG DS M368L6423FTN-CCC • • •256 MB Infineon HYB25D256800CE-5C Infineon SS HYS64D32300HU-5-C • • •512 MB Infineon HYB25D512800CE-5C Infineon SS HYS64D64300HU-5-C • • •256 MB CORSAIR W942508BH-5 – SS CMX256A-3200C2PT • • •512MB CORSAIR VS32M8-5 – DS VS512MB400 • • •512 MB Hynix HY5DU56822DT-D43 – DS HYMD264646D8J-D43 • • •512 M Transcend K4H560838F-TCCC SAMSUNG DS TS64MLD64V4F3 • • •512 MB A DATA K4H560838F-TCCC SAMSUNG DS MDOSS6F3H41Y0N1E0Z • • •256 MB A DATA HY5DU56822CT-D43 Hynix SS MDOHY6F3G31Y0N1E0Z • • •512 MB A DATA HY5DU56822CT-D43 Hynix DS MDOHY6F3H41Y0N1E0Z • • •256 MB A DATA ADD8608A8A-5B – SS MDOAD5F3G31Y0N1E02 • • •512 MB KINGMAX KDL388P4LA-50 – DS MPXC22D-38KT3R • • •

D I M M s u p p o r tD I M M s u p p o r tD I M M s u p p o r tD I M M s u p p o r tD I M M s u p p o r t

Legend :Legend :Legend :Legend :Legend :A A A A A - supports one module inserted in DIMM_B1 slot in a Single-channel memory

configuration.BBBBB - Supports one pair of modules inserted into either the blue slots or the black

slots as one pair of Dual-channel memory configuration.C C C C C - Supports 4 modules inserted into both the blue and black slots as two pairs of

Dual-channel memory configurationS SS SS SS SS S - Single-sidedD SD SD SD SD S - Double-sided

Visit the ASUS website (www.asus.com) for the latest Qualified VendorsList.

2 -142 -142 -142 -142 -14 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.4.42.4.42.4.42.4.42.4.4 Removing a DDR DIMMRemoving a DDR DIMMRemoving a DDR DIMMRemoving a DDR DIMMRemoving a DDR DIMMTo remove a DIMM:

1. Simultaneously press theretaining clips outward to unlockthe DIMM.

2. Remove the DIMM from the socket.

Support the DIMM lightly with your fingers when pressing the retainingclips. The DIMM might get damaged when it flips out with extra force.

2.4.32.4.32.4.32.4.32.4.3 Installing a DDR DIMMInstalling a DDR DIMMInstalling a DDR DIMMInstalling a DDR DIMMInstalling a DDR DIMM

3. Firmly insert the DIMM into thesocket until the retaining clipssnap back in place and the DIMMis properly seated.

1. Unlock a DIMM socket bypressing the retaining clipsoutward.

2. Align a DIMM on the socket suchthat the notch on the DIMMmatches the break on thesocket.

Locked Re ta i n i ng C l i pLocked Re ta i n i ng C l i pLocked Re ta i n i ng C l i pLocked Re ta i n i ng C l i pLocked Re ta i n i ng C l i p

Make sure to unplug the power supply before adding or removing DIMMsor other system components. Failure to do so may cause severe damageto both the motherboard and the components.

A DDR DIMM is keyed with a notch so that it fits in only one direction.DO NOT force a DIMM into a socket to avoid damaging the DIMM.

Un locked re ta i n i ng c l i pUn locked re ta i n i ng c l i pUn locked re ta i n i ng c l i pUn locked re ta i n i ng c l i pUn locked re ta i n i ng c l i p

DDR D IMM no tchDDR D IMM no tchDDR D IMM no tchDDR D IMM no tchDDR D IMM no tch

DDR D IMM no tchDDR D IMM no tchDDR D IMM no tchDDR D IMM no tchDDR D IMM no tch1

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 -152 -152 -152 -152 -15

2.5 Expansion slotsIn the future, you may need to install expansion cards. The followingsub-sections describe the slots and the expansion cards that they support.

2.5.12.5.12.5.12.5.12.5.1 Installing an expansion cardInstalling an expansion cardInstalling an expansion cardInstalling an expansion cardInstalling an expansion cardTo install an expansion card:

1. Before installing the expansion card, read the documentation thatcame with it and make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is alreadyinstalled in a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keepthe screw for later use.

4. Align the card connector with the slot and press firmly until the card iscompletely seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.6. Replace the system cover.

2.5.22.5.22.5.22.5.22.5.2 Configuring an expansion cardConfiguring an expansion cardConfiguring an expansion cardConfiguring an expansion cardConfiguring an expansion cardAfter installing the expansion card, configure it by adjusting the softwaresettings.

1. Turn on the system and change the necessary BIOS settings, if any.See Chapter 4 for information on BIOS setup.

2. Assign an IRQ to the card. Refer to the tables on the next page.3. Install the software drivers for the expansion card.

Make sure to unplug the power cord before adding or removingexpansion cards. Failure to do so may cause you physical injury anddamage motherboard components.

2 -162 -162 -162 -162 -16 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.5.32.5.32.5.32.5.32.5.3 Interrupt assignmentsInterrupt assignmentsInterrupt assignmentsInterrupt assignmentsInterrupt assignmentsStandard interrupt assignmentsStandard interrupt assignmentsStandard interrupt assignmentsStandard interrupt assignmentsStandard interrupt assignments

I R QI R QI R QI R QI R Q P r i o r i t yP r i o r i t yP r i o r i t yP r i o r i t yP r i o r i t y S tanda rd Func t i onStanda rd Func t i onStanda rd Func t i onStanda rd Func t i onStanda rd Func t i on0 1 System Timer1 2 Keyboard Controller2 — Re-direct to IRQ #93 11 Reserved4 12 Communications Port (COM1)*5 13 IRQ holder for PCI steering*6 14 Floppy Disk Controller7 15 Printer Port (LPT1)*8 3 System CMOS/Real Time Clock9 4 IRQ holder for PCI steering*10 5 IRQ holder for PCI steering*11 6 IRQ holder for PCI steering*12 7 PS/2 Compatible Mouse Port*13 8 Numeric Data Processor14 9 Primary IDE/SATA Channel15 10 Secondary IDE/SATA Channel

* These I RQs a re usua l l y ava i l ab l e fo r I SA o r PC I dev i ces .* These I RQs a re usua l l y ava i l ab l e fo r I SA o r PC I dev i ces .* These I RQs a re usua l l y ava i l ab l e fo r I SA o r PC I dev i ces .* These I RQs a re usua l l y ava i l ab l e fo r I SA o r PC I dev i ces .* These I RQs a re usua l l y ava i l ab l e fo r I SA o r PC I dev i ces .

When using PCI cards on shared slots, ensure that the drivers support“Share IRQ” or that the cards do not need IRQ assignment; otherwise,conflicts will arise between the two PCI groups, making the systemunstable and the card inoperable.

IRQ assignments for this motherboardIRQ assignments for this motherboardIRQ assignments for this motherboardIRQ assignments for this motherboardIRQ assignments for this motherboard

AAAAA BBBBB CCCCC DDDDD EEEEE FFFFF GGGGG HHHHHPCI slot 1 — shared shared shared shared — — —PCI slot 2 — — shared shared shared shared — —PCI slot 3 — — — shared shared shared shared —IEEE 1394 — — — — shared — — —PCI Express LAN (88E8053) — — shared — — — — —PCI LAN (88E8001) — — — — — shared — —PCI-E x1 shared shared shared shared — — — —PCI-E x16_1 shared shared shared shared — — — —PCI-E x16_2 shared shared shared shared — — — —Onboard USB controller 1 — shared — — — — — —Onboard USB controller 2 — — shared — — — — —Onboard USB controller 3 — — — shared — — — —Onboard USB 2.0 controller — — — shared — — — —HD audio — — — — — — shared —Serial ATA — — — shared — — — —Silicon Image SATA controller — shared — — — — — —

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 -172 -172 -172 -172 -17

2.5.42.5.42.5.42.5.42.5.4 PCI slotsPCI slotsPCI slotsPCI slotsPCI slotsThe PCI slots support cards such as aLAN card, SCSI card, USB card, andother cards that comply with PCIspecifications. The figure shows aLAN card installed on a PCI slot.

2.5.52.5.52.5.52.5.52.5.5 PCI Express x1 slotPCI Express x1 slotPCI Express x1 slotPCI Express x1 slotPCI Express x1 slotThis motherboard supports PCIExpress x1 network cards, SCSI cardsand other cards that comply with thePCI Express specifications. Thefollowing figure shows a network cardinstalled on the PCI Express x1 slot.

2.5.62.5.62.5.62.5.62.5.6 Two PCI Express x16 slotsTwo PCI Express x16 slotsTwo PCI Express x16 slotsTwo PCI Express x16 slotsTwo PCI Express x16 slotsThis motherboard supports two ATICrossFire™ PCI Express x16 graphicscards that comply with the PCIExpress specifications. The figureshows two graphics cards installed onthe PCI Express x16 slots.

See Chapter 6 for details on theCrossFire™ technology feature.

2 -182 -182 -182 -182 -18 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

• We recommend that you install a VGA card on the primary (blue) PCIExpress slot and install any other PCI Express device on thesecondary (black) PCI Express slot.

• In CrossF i re™ mode, insta l l the ATI CrossF i re™ Ed i t ionIn CrossF i re™ mode, insta l l the ATI CrossF i re™ Ed i t ionIn CrossF i re™ mode, insta l l the ATI CrossF i re™ Ed i t ionIn CrossF i re™ mode, insta l l the ATI CrossF i re™ Ed i t ionIn CrossF i re™ mode, insta l l the ATI CrossF i re™ Ed i t ion(Master) graph ics card on the pr imary (b lue) PC I(Master) graph ics card on the pr imary (b lue) PC I(Master) graph ics card on the pr imary (b lue) PC I(Master) graph ics card on the pr imary (b lue) PC I(Master) graph ics card on the pr imary (b lue) PC IExpress s lot ; otherwise , the system wi l l not boot .Express s lot ; otherwise , the system wi l l not boot .Express s lot ; otherwise , the system wi l l not boot .Express s lot ; otherwise , the system wi l l not boot .Express s lot ; otherwise , the system wi l l not boot .

• If you do not configure the PCI Express device (s) according to thetable below, the system may have a failed or delayed power-on selftest (POST).

• Refer to the table below for possible PCI Express Cardconfigurations.

PCI Express x16 slot configurationsPCI Express x16 slot configurationsPCI Express x16 slot configurationsPCI Express x16 slot configurationsPCI Express x16 slot configurations

PC IEX16_1 (b l ue ) s l o tPC I EX16_1 (b l ue ) s l o tPC I EX16_1 (b l ue ) s l o tPC I EX16_1 (b l ue ) s l o tPC I EX16_1 (b l ue ) s l o t PC I EX16_2 (b l ack ) s l o tPC I EX16_2 (b l ack ) s l o tPC I EX16_2 (b l ack ) s l o tPC I EX16_2 (b l ack ) s l o tPC I EX16_2 (b l ack ) s l o tCa r d TypeCa rd TypeCa rd TypeCa rd TypeCa rd Type S p e e dS p e e dS p e e dS p e e dS p e e d Ca rd TypeCa rd TypeCa rd TypeCa rd TypeCa rd Type S p e e dS p e e dS p e e dS p e e dS p e e d

Singlegraphics

card

PCIe x16 graphics card x16

PCIe x16 graphics card x16 PCIe devices (non-VGA) x16Dual

graphicscards in

CrossFire™mode*

ATI CrossFire Edition x16 ATI CrossFire-ready x16graphics card graphics card

* In CrossFire™ mode, install two ATI graphics cards from the sameGPU family.

Graphics card x16 Graphics card x16Dual

graphicscards (Dual

display)

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 2 -192 -192 -192 -192 -19

2.6 JumperClear RTC RAM (CLRTC)Clear RTC RAM (CLRTC)Clear RTC RAM (CLRTC)Clear RTC RAM (CLRTC)Clear RTC RAM (CLRTC)This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.You can clear the CMOS memory of date, time, and system setupparameters by erasing the CMOS RTC RAM data. The onboard button cellbattery powers the RAM data in CMOS, which include system setupinformation such as system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.2. Remove the onboard battery.3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the

cap on pins 2-3 for about 5~10 seconds, then move the cap back topins 1-2.

4. Reinstall the battery.5. Plug the power cord and turn ON the computer.6. Hold down the <Del> key during the boot process and enter BIOS

setup to re-enter data.

Except when clearing the RTC RAM, never remove the cap on CLRTCjumper default position. Removing the cap will cause system boot failure!

You do not need to clear the RTC when the system hangs due tooverclocking. For system failure due to overclocking, use the C.P.R. (CPUParameter Recall) feature. Shut down and reboot the system so the BIOScan automatically reset parameter settings to default values.

A8R32-MVP DELUXE

A8R32-MVP DELUXE Clear RTC RAM

CLRTC

Normal Clear CMOS(Default)

1 2 2 3

2 -202 -202 -202 -202 -20 Chapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ionChapter 2 : Hardware in format ion

2.7 Connectors

2.7.12.7.12.7.12.7.12.7.1 Rear panel connectorsRear panel connectorsRear panel connectorsRear panel connectorsRear panel connectors

1 .1 .1 .1 .1 . PS/2 mouse port (green).PS/2 mouse port (green).PS/2 mouse port (green).PS/2 mouse port (green).PS/2 mouse port (green). This port is for a PS/2 mouse.2 .2 .2 .2 .2 . Para l le l port .Para l le l port .Para l le l port .Para l le l port .Para l le l port . This 25-pin port connects a parallel printer, a scanner,

or other devices.3 .3 .3 .3 .3 . S ide Speaker Out port (b lack). S ide Speaker Out port (b lack). S ide Speaker Out port (b lack). S ide Speaker Out port (b lack). S ide Speaker Out port (b lack). This port connects the side

speakers in an 8-channel audio configuration.4 .4 .4 .4 .4 . Center/Subwoofer port (orange). Center/Subwoofer port (orange). Center/Subwoofer port (orange). Center/Subwoofer port (orange). Center/Subwoofer port (orange). This port connects the

center/subwoofer speakers.5 .5 .5 .5 .5 . L ine In port ( l ight b lue).L ine In port ( l ight b lue).L ine In port ( l ight b lue).L ine In port ( l ight b lue).L ine In port ( l ight b lue). This port connects a tape, CD, DVD

player, or other audio sources.6 .6 .6 .6 .6 . L ine Out port ( l ime).L ine Out port ( l ime).L ine Out port ( l ime).L ine Out port ( l ime).L ine Out port ( l ime). This port connects a headphone or a

speaker. In 4-channel, 6-channel, and 8-channel configuration, thefunction of this port becomes Front Speaker Out.

Refer to the audio configuration table below for the function of theaudio ports in 2, 4, or 6, or 8-channel configuration.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 - 94 - 94 - 94 - 94 - 9

Bad BIOS checksum. Starting BIOS recovery...

Checking for floppy...

4. Restart the system after the utility completes the updating process.

Bad BIOS checksum. Starting BIOS recovery...Checking for floppy...Floppy found!Reading file “A8R32-MVP.ROM”. Completed.Start flashing...

When found, the utility reads the BIOS file and starts flashing thecorrupted BIOS file.

DO NOT shut down or reset the system while updating the BIOS! Doingso can cause system boot failure!

4.1.54.1.54.1.54.1.54.1.5 ASUS CrashFree BIOS 2 utilityASUS CrashFree BIOS 2 utilityASUS CrashFree BIOS 2 utilityASUS CrashFree BIOS 2 utilityASUS CrashFree BIOS 2 utilityThe ASUS CrashFree BIOS 2 is an auto recovery tool that allows you torestore the BIOS file when it fails or gets corrupted during the updatingprocess. You can update a corrupted BIOS file using the motherboardsupport CD or the floppy disk that contains the updated BIOS file.

Recovering the BIOS from a floppy diskRecovering the BIOS from a floppy diskRecovering the BIOS from a floppy diskRecovering the BIOS from a floppy diskRecovering the BIOS from a floppy diskTo recover the BIOS from a floppy disk:

1. Turn on the system.2. Insert the floppy disk with the original or updated BIOS file to the

floppy disk drive.3. The utility displays the following message and automatically checks

the floppy disk for the original or updated BIOS file.

• Prepare the motherboard support CD or the floppy disk containingthe updated motherboard BIOS before using this utility.

• Make sure that you rename the original or updated BIOS file in thefloppy disk to A8R32-MVP.ROM.A8R32-MVP.ROM.A8R32-MVP.ROM.A8R32-MVP.ROM.A8R32-MVP.ROM.

4 -104 -104 -104 -104 -10 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Recovering the BIOS from the support CDRecovering the BIOS from the support CDRecovering the BIOS from the support CDRecovering the BIOS from the support CDRecovering the BIOS from the support CDTo recover the BIOS from the support CD:

1. Remove any floppy disk from the floppy disk drive, then turn on thesystem.

2. Insert the support CD to the optical drive.3. The utility displays the following message and automatically checks

the floppy disk for the original or updated BIOS file.

Bad BIOS checksum. Starting BIOS recovery...Checking for floppy...Floppy not found!Checking for CD-ROM...CD-ROM found!Reading file “A8R32-MVP.ROM”. Completed.Start flashing...

When no floppy disk is found, the utility automatically checks theoptical drive for the original or updated BIOS file. The utility thenupdates the corrupted BIOS file.

Bad BIOS checksum. Starting BIOS recovery...Checking for floppy...

The recovered BIOS may not be the latest BIOS version for thismotherboard. Visit the ASUS website (www.asus.com) to download thelatest BIOS file.

4. Restart the system after the utility completes the updating process.

DO NOT shut down or reset the system while updating the BIOS! Doingso can cause system boot failure!

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -114 -114 -114 -114 -11

4.2 BIOS setup programThis motherboard supports a programmable firmware chip that you canupdate using the provided utility described in section “4.1 Managing andupdating your BIOS.”

Use the BIOS Setup program when you are installing a motherboard,reconfiguring your system, or prompted to “Run Setup.” This sectionexplains how to configure your system using this utility.

Even if you are not prompted to use the Setup program, you can changethe configuration of your computer in the future. For example, you canenable the security password feature or change the power managementsettings. This requires you to reconfigure your system using the BIOSSetup program so that the computer can recognize these changes andrecord them in the CMOS RAM or the firmware hub.

The firmware hub on the motherboard stores the Setup utility. When youstart up the computer, the system provides you with the opportunity torun this program. Press <Del> during the Power-On-Self-Test (POST) toenter the Setup utility; otherwise, POST continues with its test routines.

If you wish to enter Setup after POST, restart the system by pressing<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis.You can also restart by turning the system off and then back on. Do thislast option only if the first two failed.

The Setup program is designed to make it as easy to use as possible. Beinga menu-driven program, it lets you scroll through the various sub-menusand make your selections from the available options using the navigationkeys.

• The default BIOS settings for this motherboard apply for mostconditions to ensure optimum performance. If the system becomesunstable after changing any BIOS settings, load the default settingsto ensure system compatibility and stability. Select the L o a dL o a dL o a dL o a dL o a dDefau l t Sett ingsDefau l t Sett ingsDefau l t Sett ingsDefau l t Sett ingsDefau l t Sett ings item under the Exit Menu. See section “4.7 ExitMenu.”

• The BIOS setup screens shown in this section are for referencepurposes only, and may not exactly match what you see on yourscreen.

• Visit the ASUS website (www.asus.com) to download the latest BIOSfile for this motherboard.

4 -124 -124 -124 -124 -12 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change FieldTab Select FieldF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain Advanced Power Boot Exit

4.2.24.2.24.2.24.2.24.2.2 Menu barMenu barMenu barMenu barMenu barThe menu bar on top of the screen has the following main items:

Ma inMa inMa inMa inMa in For changing the basic system configurationAdvancedAdvancedAdvancedAdvancedAdvanced For changing the advanced system settingsPowerPowerPowerPowerPower For changing the advanced power management (APM)

configurationBootBootBootBootBoot For changing the system boot configurationEx i tEx i tEx i tEx i tEx i t For selecting the exit options and loading default

settings

To select an item on the menu bar, press the right or left arrow key on thekeyboard until the desired item is highlighted.

4.2.34.2.34.2.34.2.34.2.3 Navigation keysNavigation keysNavigation keysNavigation keysNavigation keysAt the bottom right corner of a menu screen are the navigation keys forthat particular menu. Use the navigation keys to select items in the menuand change the settings.

Some of the navigation keys differ from one screen to another.

4.2.14.2.14.2.14.2.14.2.1 BIOS menu screenBIOS menu screenBIOS menu screenBIOS menu screenBIOS menu screen

System Time [10:55:25]System Date [Thu 12/15/2005]Legacy Diskette A [1.44M, 3.5 in]Language [English]

Primary IDE Master [ST320410A]Primary IDE Slave [ASUS CD-S520/A]Secondary IDE Master [Not Detected]Secondary IDE Slave [Not Detected]Third IDE Master [Not Detected]Third IDE Slave [Not Detected]Fourt IDE Master [Not Detected]Fourth IDE Slave [Not Detected]Storage Configuration

System Information

Use [ENTER], [TAB] or[SHIFT-TAB] to selecta field.

Use [+] or [-] toconfigure the SystemTime.

Nav iga t i on keysNav i ga t i on keysNav i ga t i on keysNav i ga t i on keysNav i ga t i on keys

Gene r a l he l pGene r a l he l pGene r a l he l pGene r a l he l pGene r a l he l pMenu ba rMenu ba rMenu ba rMenu ba rMenu ba r

Sub -menu i t emsSub -menu i t emsSub -menu i t emsSub -menu i t emsSub -menu i t ems

Con f i gu ra t i on f i e l d sCon f i gu ra t i on f i e l d sCon f i gu ra t i on f i e l d sCon f i gu ra t i on f i e l d sCon f i gu ra t i on f i e l d sMenu i t emsMenu i t emsMenu i t emsMenu i t emsMenu i t ems

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -134 -134 -134 -134 -13

4.2.44.2.44.2.44.2.44.2.4 Menu itemsMenu itemsMenu itemsMenu itemsMenu itemsThe highlighted item on the menubar displays the specific items forthat menu. For example, selectingMa in Ma in Ma in Ma in Ma in shows the Main menu items.

The other items (Advanced,Power, Boot, and Exit) on themenu bar have their respectivemenu items.

4.2.54.2.54.2.54.2.54.2.5 Sub-menu itemsSub-menu itemsSub-menu itemsSub-menu itemsSub-menu itemsA solid triangle before each item on any menu screen means that the iteamhas a sub-menu. To display the sub-menu, select the item and press<Enter>.

4.2.64.2.64.2.64.2.64.2.6 Configuration fieldsConfiguration fieldsConfiguration fieldsConfiguration fieldsConfiguration fieldsThese fields show the values for the menu items. If an item is user-configurable, you can change the value of the field opposite the item. Youcannot select an item that is not user-configurable.

A configurable field is enclosed in brackets, and is highlighted whenselected. To change the value of a field, select it then press <Enter> todisplay a list of options. Refer to “4.2.7 Pop-up window.”

4.2.74.2.74.2.74.2.74.2.7 Pop-up windowPop-up windowPop-up windowPop-up windowPop-up windowSelect a menu item then press <Enter> to display a pop-up window withthe configuration options for that item.

4.2.84.2.84.2.84.2.84.2.8 Scroll barScroll barScroll barScroll barScroll barA scroll bar appears on the rightside of a menu screen when thereare items that do not fit on thescreen. Press theUp/Down arrow keys or <PageUp> /<Page Down> keys todisplay the other items on thescreen.

4.2.94.2.94.2.94.2.94.2.9 General helpGeneral helpGeneral helpGeneral helpGeneral helpAt the top right corner of the menu screen is a brief description of theselected item.

Ma i n menu i t emsMa i n menu i t emsMa i n menu i t emsMa i n menu i t emsMa i n menu i t ems

Use [ENTER], [TAB],or [SHIFT-TAB] toselect a field.

Use [+] or [-] toconfigure systemtime.

Select ScreenSelect Item

+- Change FieldTab Select FieldF1 General HelpF10 Save and ExitESC Exit

System Time [10:55:25]System Date [Wed 10/25/2005]Legacy Diskette A [1.44M, 3.5 in.]Language [English]

Primary IDE Master [ST320410A]Primary IDE Slave [ASUS CD-S520/A]Secondary IDE Master[Not Detected]Secondary IDE Slave [Not Detected]Third IDE Master [Not Detected]Third IDE Slave [Not Detected]Fourth IDE Master [Not Detected]Fourth IDE Slave [Not Detected]Storage Configuration

System Information

BIOS SETUP UTILITYMain Advanced Power Boot Exit

Advanced PCI/PnP Settings

WARNING: Setting wrong values inbelow sections may cause system tomalfunction.

Plug And Play O/S [No]PCI Latency Timer [64]Allocate IRQ to PCI VGA [Yes]Palette Snooping [Disabled]PCI IDE BusMaster [Enabled]

Sc ro l l b a rSc ro l l b a rSc ro l l b a rSc ro l l b a rSc ro l l b a r

Pop -up w i ndowPop -up w i ndowPop -up w i ndowPop -up w i ndowPop -up w i ndow

4 -144 -144 -144 -144 -14 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change FieldTab Select FieldF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain Advanced Power Boot Exit

4.3 Main menuWhen you enter the BIOS Setup program, the Ma in Ma in Ma in Ma in Ma in menu screen appears,giving you an overview of the basic system information.

4.3.14.3.14.3.14.3.14.3.1 System Time [xx:xx:xx]System Time [xx:xx:xx]System Time [xx:xx:xx]System Time [xx:xx:xx]System Time [xx:xx:xx]Allows you to set the system time.

4.3.24.3.24.3.24.3.24.3.2 System Date [Day xx/xx/xxxx]System Date [Day xx/xx/xxxx]System Date [Day xx/xx/xxxx]System Date [Day xx/xx/xxxx]System Date [Day xx/xx/xxxx]Allows you to set the system date.

4.3.34.3.34.3.34.3.34.3.3 Legacy Diskette A [1.44M, 3.5 in.]Legacy Diskette A [1.44M, 3.5 in.]Legacy Diskette A [1.44M, 3.5 in.]Legacy Diskette A [1.44M, 3.5 in.]Legacy Diskette A [1.44M, 3.5 in.]Sets the type of floppy drive installed. Configuration options: [Disabled][360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.][2.88M, 3.5 in.]

4.3.44.3.44.3.44.3.44.3.4 Language [English]Language [English]Language [English]Language [English]Language [English]Allows you to choose the BIOS language version from the options.Configuration options: [Chinese (BIG5)] [Chinese (GB)] [Japanese][Français] [German] [English]

Refer to section “4.2.1 BIOS menu screen” for information on the menuscreen items and how to navigate through them.

System Time [10:55:25]System Date [Mon 10/25/2005]Legacy Diskette A [1.44M, 3.5 in]Language [English]

Primary IDE Master [ST320410A] Primary IDE Slave [ASUS CD-S520/A] Secondary IDE Master [Not Detected] Secondary IDE Slave [Not Detected] Third IDE Master [Not Detected] Third IDE Slave [Not Detected] Fourth IDE Master [Not Detected] Fourth IDE Slave [Not Detected] Storage Configuration

System Information

Use [ENTER], [TAB] or[SHIFT-TAB] to selecta field.

Use [+] or [-] toconfigure the SystemTime.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -154 -154 -154 -154 -15

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain

4.3.54.3.54.3.54.3.54.3.5 Primary, Secondary, Third, and FourthPrimary, Secondary, Third, and FourthPrimary, Secondary, Third, and FourthPrimary, Secondary, Third, and FourthPrimary, Secondary, Third, and FourthIDE Master/SlaveIDE Master/SlaveIDE Master/SlaveIDE Master/SlaveIDE Master/Slave

The BIOS automatically detects the connected IDE devices. There is aseparate sub-menu for each IDE device. Select a device item, then press<Enter> to display the IDE device information.

The BIOS automatically detects the values opposite the dimmed items(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, UltraDMA, and SMART monitoring). These values are not user-configurable.These items show N/A if no IDE device is installed in the system.

Type [Auto]Type [Auto]Type [Auto]Type [Auto]Type [Auto]Selects the type of IDE drive. Setting to [Auto] allows automatic selectionof the appropriate IDE device type. Select [CDROM] if you are specificallyconfiguring a CD-ROM drive. Select [ARMD] (ATAPI Removable MediaDevice) if your device is either a ZIP, LS-120, or MO drive.Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]

LBA/Large Mode [Auto]LBA/Large Mode [Auto]LBA/Large Mode [Auto]LBA/Large Mode [Auto]LBA/Large Mode [Auto]Enables or disables the LBA mode. Setting to [Auto] enables the LBA modeif the device supports this mode, and if the device was not previouslyformatted with LBA mode disabled. Configuration options: [Disabled][Auto]

Block (Multi-sector Transfer) M [Auto]Block (Multi-sector Transfer) M [Auto]Block (Multi-sector Transfer) M [Auto]Block (Multi-sector Transfer) M [Auto]Block (Multi-sector Transfer) M [Auto]Enables or disables data multi-sectors transfers. When set to [Auto], thedata transfer from and to the device occurs multiple sectors at a time ifthe device supports multi-sector transfer feature. When set to [Disabled],the data transfer from and to the device occurs one sector at a time.Configuration options: [Disabled] [Auto]

Primary IDE Master

Device : Hard DiskVendor : ST320413ASize : 20.0GBLBA Mode : SupportedBlock Mode : 16 SectorsPIO Mode : 4Async DMA : MultiWord DMA-2Ultra DMA : Ultra DMA-6SMART Monitoring: Supported

Type [Auto]LBA/Large Mode [Auto]Block(Multi-sector Transfer) M [Auto]PIO Mode [Auto]DMA Mode [Auto]SMART Monitoring [Auto]32Bit Data Transfer [Disabled]

Select the type ofdevice connected tothe system.

4 -164 -164 -164 -164 -16 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain

PIO Mode [Auto]PIO Mode [Auto]PIO Mode [Auto]PIO Mode [Auto]PIO Mode [Auto]Selects the PIO mode.Configuration options: [Auto] [0] [1] [2] [3] [4]

DMA Mode [Auto]DMA Mode [Auto]DMA Mode [Auto]DMA Mode [Auto]DMA Mode [Auto]Selects the DMA mode. Configuration options: [Auto] [SWDMA0][SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0][UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] [UDMA6]

SMART Monitoring [Auto]SMART Monitoring [Auto]SMART Monitoring [Auto]SMART Monitoring [Auto]SMART Monitoring [Auto]Sets the Smart Monitoring, Analysis, and Reporting Technology.Configuration options: [Auto] [Disabled] [Enabled]

32Bit Data Transfer [Disabled]32Bit Data Transfer [Disabled]32Bit Data Transfer [Disabled]32Bit Data Transfer [Disabled]32Bit Data Transfer [Disabled]Enables or disables 32-bit data transfer.Configuration options: [Disabled] [Enabled]

4.3.64.3.64.3.64.3.64.3.6 Storage ConfigurationStorage ConfigurationStorage ConfigurationStorage ConfigurationStorage Configuration

Storage Configuration

Serial ATA Controller [Enabled]RAID Mode Selection [SATA mode]SATA Mode Selection [Emulated PATA Mode]

Serial ATA ControllerSerial ATA ControllerSerial ATA ControllerSerial ATA ControllerSerial ATA Controller [Enabled][Enabled][Enabled][Enabled][Enabled]Allows you to enable or disable the Serial ATA controller.Configuration options: [Disabled] [Enabled]

Options

DisabledEnabled

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -174 -174 -174 -174 -17

Select Screen Select Item

F1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain

The succeeding items appear only if the Ser ia l ATA Contro l le r Ser ia l ATA Contro l le r Ser ia l ATA Contro l le r Ser ia l ATA Contro l le r Ser ia l ATA Contro l le r itemis set to [Enabled].

RAID Mode Selection [SATA mode]Allows you to select the RAID mode.Configuration options: [SATA mode] [RAID mode]

SATA Mode Selection [Emulated PATA Mode]Allows you to select the Serial ATA mode.Configuration options: [Emulated PATA Mode] [AHCI Mode]

4.3.74.3.74.3.74.3.74.3.7 System InformationSystem InformationSystem InformationSystem InformationSystem InformationThis menu gives you an overview of the general system specifications. TheBIOS automatically detects the items in this menu.

AMI BIOSAMI BIOSAMI BIOSAMI BIOSAMI BIOSDisplays the auto-detected BIOS information.

ProcessorProcessorProcessorProcessorProcessorDisplays the auto-detected CPU specification.

System MemorySystem MemorySystem MemorySystem MemorySystem MemoryDisplays the auto-detected system memory.

AMIBIOSVersion : 0111Build Date : 12/28/05

ProcessorType : AMD Athlon(tm) 64 Processor 3200+Speed : 2000 MHzCount : 1

System MemorySize : 512 MB

4 -184 -184 -184 -184 -18 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change optionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain Advanced Power Boot Exit

Select Screen Select Item

+- Change optionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

4.4 Advanced menuThe Advanced menu items allow you to change the settings for the CPUand other system devices.

Take caution when changing the settings of the Advanced menu items.Incorrect field values can cause the system to malfunction.

Jumperfree ConfigurationCPU ConfigurationChipset

Onboard Devices ConfigurationPCIPnPLAN Cable StatusUSB Configuration

Configure System Frequency/Voltage

AI Overclocking [Auto]

FID/VID Change [Auto]DDR Voltage [Auto]VCORE Over-voltage [Auto]Northbridge Over-voltage [Auto]Southbridge Over-voltage [Auto]

PEG Link Mode [Disabled]PEG Buffer Length [Auto]

BankA DDR Clock Skew [Auto]BankB DDR Clock Skew [Auto]

4.4.14.4.14.4.14.4.14.4.1 JumperFree ConfigurationJumperFree ConfigurationJumperFree ConfigurationJumperFree ConfigurationJumperFree Configuration

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -194 -194 -194 -194 -19

AI Overclocking [Auto]AI Overclocking [Auto]AI Overclocking [Auto]AI Overclocking [Auto]AI Overclocking [Auto]Allows you to select the overclocking options to achieve the desired CPUinternal frequency. Select either one of the preset overclockingconfigiuration options.

S e t t i n gS e t t i n gS e t t i n gS e t t i n gS e t t i n g Desc r i p t i onDesc r i p t i onDesc r i p t i onDesc r i p t i onDesc r i p t i on

Manua lManua lManua lManua lManua l allows you to individually set overclocking parameters.Au toAu toAu toAu toAu to loads the optimal settings for the system.StandardStandardStandardStandardStandard loads the standard settings for the system.Overc lock Prof i l eOverc lock Prof i l eOverc lock Prof i l eOverc lock Prof i l eOverc lock Prof i l e loads overclocking profiles with optimal

parameters for stability when overclocking.A I N .O .S .A I N .O .S .A I N .O .S .A I N .O .S .A I N .O .S . the ASUS AI Non-delay Overclocking System feature

intelligently determines the system load andautomatically boost the performance for the mostdemanding tasks.

FID/VID Change [Auto]FID/VID Change [Auto]FID/VID Change [Auto]FID/VID Change [Auto]FID/VID Change [Auto]When set to [Auto], FID/VID will be set at the rated frequency/voltage.When set to [Manual], FID/VID will be set based on the user selection.

The following items appear only when the F ID/V ID Change i tem F ID/VID Change i tem F ID/VID Change i tem F ID/VID Change i tem F ID/VID Change i tem isset to [Manual].

Processor Frequency Multipl ier [x4]Processor Frequency Multipl ier [x4]Processor Frequency Multipl ier [x4]Processor Frequency Multipl ier [x4]Processor Frequency Multipl ier [x4]Allows you to set the processor frequency multiplier.Configuration options: [x4] [x4.5] [x5]... [x25.5]

Processor Voltage [1.450 V]Processor Voltage [1.450 V]Processor Voltage [1.450 V]Processor Voltage [1.450 V]Processor Voltage [1.450 V]Allows you to set the processor voltage.Configuration options: [1.450 V] [1.425 V] [1.400 V]... [0.800 V]

DDR Voltage [Auto]DDR Voltage [Auto]DDR Voltage [Auto]DDR Voltage [Auto]DDR Voltage [Auto]Allows you to set the DDR memory voltage.Configuration options: [Auto] [2.60 V] [2.65 V]...[3.20 V]

Setting a very high voltage may damage the component permanently.Setting a very low voltage may cause the system to become unstable.

VCORE Over-voltage [Auto]VCORE Over-voltage [Auto]VCORE Over-voltage [Auto]VCORE Over-voltage [Auto]VCORE Over-voltage [Auto]Allows you to enable or disable VCORE over-voltage.Configuration options: [Auto] [Disabled] [Enable] [+100mV] [+200mV]

4 -204 -204 -204 -204 -20 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

CPU Frequency [XXX]CPU Frequency [XXX]CPU Frequency [XXX]CPU Frequency [XXX]CPU Frequency [XXX]Allows you to adjust the CPU frequency. The value of this item isauto-detected by the BIOS. Use the <+><+><+><+><+> and < ->< ->< ->< ->< -> keys to adjust the CPUFSB frequency. You can also type the desired CPU frequency using thenumeric keypad. The values range from 200 to 400.

PCIE Frequency [XXX]PCIE Frequency [XXX]PCIE Frequency [XXX]PCIE Frequency [XXX]PCIE Frequency [XXX]Allows you to adjust the PCIE frequency. The value of this item isauto-detected by the BIOS. Use the <+><+><+><+><+> and < ->< ->< ->< ->< -> keys to adjust the PCIEFSB frequency. You can also type the desired PCIE frequency using thenumeric keypad. The values range from 100 to 150.

The following item appears only when you set the A I Overc lock ingA I Overc lock ingA I Overc lock ingA I Overc lock ingA I Overc lock ingitem to [Ovrerclock Profile].

BankA DDR Clock Skew [Auto]BankA DDR Clock Skew [Auto]BankA DDR Clock Skew [Auto]BankA DDR Clock Skew [Auto]BankA DDR Clock Skew [Auto]Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps]...[Advance 900] [Delay 150ps] [Delay 300ps]...[Delay 900]

BankB DDR Clock Skew [Auto]BankB DDR Clock Skew [Auto]BankB DDR Clock Skew [Auto]BankB DDR Clock Skew [Auto]BankB DDR Clock Skew [Auto]Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps]...[Advance 900] [Delay 150ps] [Delay 300ps]...[Delay 900]

The following items appear only when you set the A I Overc lock ingA I Overc lock ingA I Overc lock ingA I Overc lock ingA I Overc lock ingitem to [Manual].

Northbridge Over-voltage [Auto]Northbridge Over-voltage [Auto]Northbridge Over-voltage [Auto]Northbridge Over-voltage [Auto]Northbridge Over-voltage [Auto]Configuration options: [Auto] [Disabled] [Enabled]

Southbridge Over-voltage [Auto]Southbridge Over-voltage [Auto]Southbridge Over-voltage [Auto]Southbridge Over-voltage [Auto]Southbridge Over-voltage [Auto]Configuration options: [Auto] [Disabled] [Enabled]

PEG Link Mode [Disabled]PEG Link Mode [Disabled]PEG Link Mode [Disabled]PEG Link Mode [Disabled]PEG Link Mode [Disabled]Sets the PCI Express graphics (PEG) link mode. Setting this item to [Auto]allows the motherboard to automatically adjust the PCI Express graphicslink mode to the correct frequency based on the system configuration.Three additional settings are available for overclocking the PEG Link Mode.Configuration options: [Auto] [Disabled] [Normal] [Fast] [Faster]

PEG Buffer Length [Auto]PEG Buffer Length [Auto]PEG Buffer Length [Auto]PEG Buffer Length [Auto]PEG Buffer Length [Auto]Allows you to set the PEG buffer length.Configuration options: [Auto] [Short] [Long] [Longer] [Longest]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -214 -214 -214 -214 -21

Overclock Options [Overclock 5%]Overclock Options [Overclock 5%]Overclock Options [Overclock 5%]Overclock Options [Overclock 5%]Overclock Options [Overclock 5%]Allows you to overclock the CPU speed through the available preset values.Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 10%][Overclock 15%] [Overclock 20%] [Overclock 30%]

The following item appears only when you set the A I Overc lock ingA I Overc lock ingA I Overc lock ingA I Overc lock ingA I Overc lock ingitem to [AI N.O.S.].

Turbo N.O.S. [Overclock 3%]Turbo N.O.S. [Overclock 3%]Turbo N.O.S. [Overclock 3%]Turbo N.O.S. [Overclock 3%]Turbo N.O.S. [Overclock 3%]Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 7%][Overclock 10%] [Overclock 15%] [Overclock 20%]

4 -224 -224 -224 -224 -22 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

4.4.24.4.24.4.24.4.24.4.2 CPU ConfigurationCPU ConfigurationCPU ConfigurationCPU ConfigurationCPU ConfigurationThe items in this menu show the CPU-related information that the BIOSautomatically detects.

GART Error ReportingGART Error ReportingGART Error ReportingGART Error ReportingGART Error Reporting [Disabled][Disabled][Disabled][Disabled][Disabled]Allows you to enable or disable GART error checking for testing purposes.Configuration options: [Disabled] [Enabled]

MTRR Mapping [Continuous]MTRR Mapping [Continuous]MTRR Mapping [Continuous]MTRR Mapping [Continuous]MTRR Mapping [Continuous]Determines the method used for programming processor MTRRs when usingmore than 4 GB of system memory. Setting to [Discrete] leaves the PCIhole below the 4 GB boundary undescribed. [Continuous] explicitlydescribes the PCI hole as non-cacheable. Configuration options:[Continuous] [Discrete]

Cool ‘n’ Quiet [Cool ‘n’ Quiet [Cool ‘n’ Quiet [Cool ‘n’ Quiet [Cool ‘n’ Quiet [DisabledDisabledDisabledDisabledDisabled]]]]]Enables or disables the Cool ‘n’ Quiet™ technology feature.Configuration options: [Enabled] [Disabled]

HT Link Speed [Auto]HT Link Speed [Auto]HT Link Speed [Auto]HT Link Speed [Auto]HT Link Speed [Auto]Allows you to set the speed at which the HyperTransport link will run if thespeed is lower than or equal to the system clock and if the board iscapable. Configuration options: [Auto] [200 MHz] [400 MHz] [600 MHz][800 MHz] [1 GHz]

CPU ConfigurationModule Version: 14.08Physical Count: 1Logical Count: 1

AMD Athlon(tm) 64 Processor 3200+Revision: D0Cache L1: 128KBCache L2: 512KBSpeed: 2000 MHzCurrent FSB Multiplier: 10xMaximum FSB Multiplier: 10xAble to Change Freq: YesuCode Patch Level: 0x4D

GART Error Reporting [Disabled]MTRR Mapping [Continuous]Cool `n’ Quiet [Disabled]HT Link Speed [Auto]

This option shouldremain disabled forthe normal operation.The driver developermay enable it fortesting purpose.

Memory Configuration

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -234 -234 -234 -234 -23

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

Memory ConfigurationMemory ConfigurationMemory ConfigurationMemory ConfigurationMemory Configuration

Memory Configuration

Memory Timing ConfigurationECC Configuration

Memory CLK : 166 MHzCAS Latency (Tcl) : 2.5RAS/CAS Delay (Trcd) : 3 CLKMin Active RAS (Tras) : 7 CLKRow Precharge Time (Trp) : 3 CLKRAS/RAS Delay (Trrd) : 2 CLKRow Cycle (Trc) : 10 CLKRow Refresh Cycle (Trfc) : 12 CLKRead Write Delay (Trwt) : 4 CLKRead Preamble : 6.0 nsAsynchronous Latency : 7 ns

Memory Timing ConfigurationMemory Timing ConfigurationMemory Timing ConfigurationMemory Timing ConfigurationMemory Timing Configuration

Memory Configuration

Memclock Mode [Auto]MCT Timing Mode [Auto]MCT Extra Timing Mode [Auto]User Config Mode [Auto]Bank Interleaving [Auto]Burst Length [4 Beats]SoftWare Memory Hole [Disabled]

MEMCLK can be set bythe code using AUTO,or if you use LIMIT,you can set one ofthe standard values.

Memclock Mode [Auto][Auto] allows the BIOS to set the memclock mode automatically.[Limit] allows you to select from any of the standard values.Configuration options: [Auto] [Limit]

The following item appears when the Memc lock Mode Memc lock Mode Memc lock Mode Memc lock Mode Memc lock Mode item is set to[Limit].

Memc lock Va l ue [200 MHz]Memc lock Va l ue [200 MHz]Memc lock Va l ue [200 MHz]Memc lock Va l ue [200 MHz]Memc lock Va l ue [200 MHz]Allows you to set the memclock value.Configuration options: [100 MHz] [133 MHz] [166 MHz] [183 MHz] [200 MHz] [216MHz] [233 MHz] [250 MHz]

4 -244 -244 -244 -244 -24 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

MCT Timing Mode [Auto][Auto] allows the BIOS to set the MCT timing mode automatically.[Manual] allows you to set the values by yourself.Configuration options: [Auto] [Manual]

The following items appear when the MCT T im ing Mode MCT T im ing Mode MCT T im ing Mode MCT T im ing Mode MCT T im ing Mode item is setto [Manual].

CAS La tency (CL) [Auto]CAS La tency (CL) [Auto]CAS La tency (CL) [Auto]CAS La tency (CL) [Auto]CAS La tency (CL) [Auto]Configuration options: [Auto] [2.0] [3.0] [2.5]

TRAS [Au to ]TRAS [Au to ]TRAS [Au to ]TRAS [Au to ]TRAS [Au to ]Configuration options: [Auto] [5 CLK] [6 CLK]... [15 CLK]

TRP [Au to ]TRP [Au to ]TRP [Au to ]TRP [Au to ]TRP [Au to ]Configuration options: [Auto] [2 CLK] [3 CLK]... [6 CLK]

TRCD [Au to ]TRCD [Au to ]TRCD [Au to ]TRCD [Au to ]TRCD [Au to ]Configuration options: [Auto] [2 CLK] [3 CLK]... [6 CLK]

TRRD [Au to ]TRRD [Au to ]TRRD [Au to ]TRRD [Au to ]TRRD [Au to ]Configuration options: [Auto] [2T] [3T] [4T]

TRC [Au to ]TRC [Au to ]TRC [Au to ]TRC [Au to ]TRC [Au to ]Configuration options: [Auto] [7T] [8T] [9T]... [22T]

TRFC [Au to ]TRFC [Au to ]TRFC [Au to ]TRFC [Au to ]TRFC [Au to ]Configuration options: [Auto] [9T] [10T] [11T]... [24T]

TRWT [Au to ]TRWT [Au to ]TRWT [Au to ]TRWT [Au to ]TRWT [Au to ]Configuration options: [Auto] [1 CLK] [2 CLK]... [6 CLK]

MCT Extra Timing Mode [Auto]Allows you to manually configure the MCT Timing Mode parameters. .Configuration options: [Auto] [Manual]

The following items appear when the MCT Ext ra T im ing ModeMCT Ext ra T im ing ModeMCT Ext ra T im ing ModeMCT Ext ra T im ing ModeMCT Ext ra T im ing Mode itemis set to [Manual].

TREF [7 .8us ]TREF [7 .8us ]TREF [7 .8us ]TREF [7 .8us ]TREF [7 .8us ]

Configuration options: [15.6us] [7.8us] [3.9us]

DDR I nput S t robe Skew [D i sab l ed]DDR I nput S t robe Skew [D i sab l ed]DDR I nput S t robe Skew [D i sab l ed]DDR I nput S t robe Skew [D i sab l ed]DDR I nput S t robe Skew [D i sab l ed]

Configuration options: [Disabled] [Slower] [Faster]

DDR Data D r i v i ng S t rengthDDR Data D r i v i ng S t rengthDDR Data D r i v i ng S t rengthDDR Data D r i v i ng S t rengthDDR Data D r i v i ng S t rength

Configuration options: [Disabled] [15% Reduced] [30% Reduced][45% Reduced]

Burs t20pt [D i sab l ed ]Bu r s t20pt [D i sab l ed ]Bu r s t20pt [D i sab l ed ]Bu r s t20pt [D i sab l ed ]Bu r s t20pt [D i sab l ed ]

Configuration options: [Disabled] [Enabled]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -254 -254 -254 -254 -25

User Config Mode [Auto]Configuration options: [Auto] [Manual]

The following items appear when the User Conf ig Mode User Conf ig Mode User Conf ig Mode User Conf ig Mode User Conf ig Mode item is setto [Manual].

Read P reamb le [5 .5ns ]Read P reamb le [5 .5ns ]Read P reamb le [5 .5ns ]Read P reamb le [5 .5ns ]Read P reamb le [5 .5ns ]

Configuration options: [2.0ns] [2.5ns] [3.0ns]... [9.5ns]

Asyc La tency [7 .0ns ]Asyc La tency [7 .0ns ]Asyc La tency [7 .0ns ]Asyc La tency [7 .0ns ]Asyc La tency [7 .0ns ]

Configuration options: [4.0ns] [5.0ns] [6.0ns]... [11.0ns]

CMD-ADDR T im ing Mode [1T]CMD-ADDR T im ing Mode [1T]CMD-ADDR T im ing Mode [1T]CMD-ADDR T im ing Mode [1T]CMD-ADDR T im ing Mode [1T]

Configuration options: [1T] [2T]

Bank Interleaving [Auto]Sets whether to allow memory accesses to be spread out over BANKSon the same node or across nodes, decreasing access contention.Configuration options: [Disabled] [Auto]

Software Memory Hole [Disabled]Enables or disables the software memory remapping around thememory hole. Only REV E0 processors and above support this feature.Configuration options: [Disabled] [Enabled]

Burst length [4 Beats]Sets the burst length.Configuration options: [8 Beats] [4 Beats] [2 Beats]

4 -264 -264 -264 -264 -26 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

ECC ConfigurationECC ConfigurationECC ConfigurationECC ConfigurationECC Configuration

ECC Configuration

DRAM ECC Enable [Enabled]MCA DRAM ECC Logging [Disabled]ECC Chip Kill [Disabled]DRAM SCRUB REDIRECT [Disabled]DRAM BG Scrub [Disabled]

L2 Cache BG Scrub [Disabled]Data Cache BG Scrub [Disabled]

DRAM ECC allowshardware to report andcorrect memory errorsautomatically,maintaining systemintegrity.

DRAM ECC Enable [Enabled]Allows you to enable or disable DRAM ECC, which allows the hardwareto report and correct memory errors automatically to maintain systemintegrity. Configuration options: [Disabled] [Enabled]

MCA DRAM ECC Logg ing [D i sab l ed]MCA DRAM ECC Logg ing [D i sab l ed]MCA DRAM ECC Logg ing [D i sab l ed]MCA DRAM ECC Logg ing [D i sab l ed]MCA DRAM ECC Logg ing [D i sab l ed]Allows you to enable or disable MCA DRAM ECC logging/reporting.Configuration options: [Disabled] [Enabled]

ECC Ch i p K i l lECC Ch i p K i l lECC Ch i p K i l lECC Ch i p K i l lECC Ch i p K i l l [D i s ab l ed ][D i s ab l ed ][D i s ab l ed ][D i s ab l ed ][D i s ab l ed ]Allows you to enable or disable ECC chip kill.Configuration options: [Disabled] [Enabled]

DRAM SCRUB RED IRECT [D i sab l ed]DRAM SCRUB RED IRECT [D i sab l ed]DRAM SCRUB RED IRECT [D i sab l ed]DRAM SCRUB RED IRECT [D i sab l ed]DRAM SCRUB RED IRECT [D i sab l ed]Allows you to enable or disable DRAM scrub redirect, which allows the system tocorrect DRAM ECC errors immediately when they occur, even if background scrubbing ison. Configuration options: [Disabled] [Enabled]

DRAM BG Sc rub [D i sab l ed ]DRAM BG Sc rub [D i sab l ed ]DRAM BG Sc rub [D i sab l ed ]DRAM BG Sc rub [D i sab l ed ]DRAM BG Sc rub [D i sab l ed ]Allows DRAM scrubbing to correct memory errors so later reads are correct. Doing thiswhile memory is not being used improves performance. Configuration options:[Disabled] [40ns] [80ns] [160ns] [320ns] [640ns] [1.28us] [2.56us] [5.12us][10.2us] [20.5 us] [41.0us] [81.9us] [163.8us] [327.7us] [655.4us] [1.31ms][2.62ms] [5.24ms] [10.49ms] [20.97ms] [42.00ms] [84.00ms]

L2 Cache BG Scrub [Disabled]Allows the L2 Data Cache RAM to be corrected while idle.Configuration options: [Disabled] [40ns] [80ns] [160ns] [320ns][640ns] [1.28us] [2.56us] [5.12us] [10.2us] [20.5 us] [41.0us][81.9us] [163.8us] [327.7us] [655.4us] [1.31ms] [2.62ms][5.24ms] [10.49ms] [20.97ms] [42.00ms] [84.00ms]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -274 -274 -274 -274 -27

Data Cache BG Scrub [Disabled]Allows the L1 Data Cache RAM to be corrected while idle.Configuration options: [Disabled] [40ns] [80ns] [160ns] [320ns][640ns] [1.28us] [2.56us] [5.12us] [10.2us] [20.5 us] [41.0us][81.9us] [163.8us] [327.7us] [655.4us] [1.31ms] [2.62ms][5.24ms] [10.49ms] [20.97ms] [42.00ms] [84.00ms]

4.4.34.4.34.4.34.4.34.4.3 Chipset ConfigurationChipset ConfigurationChipset ConfigurationChipset ConfigurationChipset ConfigurationThe Chipset menu allows you to change the advanced chipset settings.Select an item then press <Enter> to display the sub-menu.

Select Screen Select Item

Enter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

Hyper Transport Configuration

HT Link Speed [Auto]CPU:RD580-NB HT Link Width [Auto]

RD580 HT Link Three State [Disabled]RD580 HT Drive Strength [Auto]HT Receiver Comp. Ctrl [Auto]

RD580 HT PLL Control [Auto]

Select Screen Select Item

Enter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

Radeon Xpress Configuration

ATI Northbridge :RD580ATI Northbridge Rev. :A11

Hyper Transport ConfigurationPCI Express Configuration

4 -284 -284 -284 -284 -28 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Hyper Transport ConfigurationHyper Transport ConfigurationHyper Transport ConfigurationHyper Transport ConfigurationHyper Transport ConfigurationAllows you to configure the HT links.

HT Link Speed [Auto]The HyperTransport link will run at this speed if it is slower than orequal to the system clock and the board is capable.Configuration options: [Auto] [200 MHz] [400 MHz] [600 MHz][800 MHz] [1 GHz]

CPU:RD580-NB HT Link Width [Auto]The HyperTransport link will run at this width.Configuration options: [Auto] [8 Bit] [16 Bit]

RD580 HT Link Three State [Disabled]Configuration options: [Disabled] [Enabled]

RD580 HT Drive Strength [Auto]Configuration options: [Auto] [Manual]

The following items appear when the RD580 HT Dr ive St rengthRD580 HT Dr ive St rengthRD580 HT Dr ive St rengthRD580 HT Dr ive St rengthRD580 HT Dr ive St rengthitem is set to [Manual].

HT D r i ve S t rength Va lue [Leve l 0 ]HT D r i ve S t rength Va lue [Leve l 0 ]HT D r i ve S t rength Va lue [Leve l 0 ]HT D r i ve S t rength Va lue [Leve l 0 ]HT D r i ve S t rength Va lue [Leve l 0 ]Configuration options: [Level 0] [Level 1] [Level 2]... [Level 31]

HT Rece i ve r Comp . C t r lHT Rece i ve r Comp . C t r lHT Rece i ve r Comp . C t r lHT Rece i ve r Comp . C t r lHT Rece i ve r Comp . C t r l [Au to ] [Au to ] [Au to ] [Au to ] [Au to ]Configuration options: [Auto] [Manual]

HT Rece i ve r Comp . Va l ue [Leve l 0 ]HT Rece i ve r Comp . Va l ue [Leve l 0 ]HT Rece i ve r Comp . Va l ue [Leve l 0 ]HT Rece i ve r Comp . Va l ue [Leve l 0 ]HT Rece i ve r Comp . Va l ue [Leve l 0 ]Configuration options: [Level 0] [Level 1] [Level 2]... [Level 31]

This item appears when the HT Rece iver Comp. Ctr l HT Rece iver Comp. Ctr l HT Rece iver Comp. Ctr l HT Rece iver Comp. Ctr l HT Rece iver Comp. Ctr l item is set to[Manual].

RD580 HT PLL Cont ro l [Auto]RD580 HT PLL Cont ro l [Auto]RD580 HT PLL Cont ro l [Auto]RD580 HT PLL Cont ro l [Auto]RD580 HT PLL Cont ro l [Auto]Configuration options: [Auto] [Low Speed] [High Speed]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -294 -294 -294 -294 -29

PCI Express Configuration

PCIE GFX1 Link Width [x16]PCIE GFX2 Link Width [x16]P2P Writes Between GFX Ports [Disabled]10% Extra Current for GPP [Enabled]10% Extra Current for SB [Enabled]10% Extra Current for GFX1 [Enabled]10% Extra Current for GFX2 [Enabled]

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

Advanced

Options

PCI Express ConfigurationPCI Express ConfigurationPCI Express ConfigurationPCI Express ConfigurationPCI Express ConfigurationPCIE GFX1 Link Width [x16]The PCIE GFX1 link will run at this width.Configuration options: [x1] [x2] [x4] [x8] [x16]

PCIE GFX2 Link Width [x16]The PCIE GFX2 link will run at this width.Configuration options: [x1] [x2] [x4] [x8] [x16]

P2P Writes Between GFX Ports [Disabled]Configuration options: [Disabled] [Enabled]

10% Extra Current for GPP [Enabled]Configuration options: [Disabled] [Enabled]

10% Extra Current for SB [Enabled]Configuration options: [Disabled] [Enabled]

10% Extra Current for GFX1 [Enabled]Configuration options: [Disabled] [Enabled]

10% Extra Current for GFX2 [Enabled]Configuration options: [Disabled] [Enabled]

x1x2x4x8x16

4 -304 -304 -304 -304 -30 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

4.4.44.4.44.4.44.4.44.4.4 Onboard Devices ConfigurationOnboard Devices ConfigurationOnboard Devices ConfigurationOnboard Devices ConfigurationOnboard Devices Configuration

HD Audio [HD Audio [HD Audio [HD Audio [HD Audio [EnabledEnabledEnabledEnabledEnabled]]]]]Allows you to enable or disable the HD Audio feature.Configuration options: [Disabled] [Enabled]

Onboard LAN [Enabled]Onboard LAN [Enabled]Onboard LAN [Enabled]Onboard LAN [Enabled]Onboard LAN [Enabled]Allows you to enable or disable the onchip MAC LAN.Configuration options: [Disabled] [Enabled]

Onboard LAN Boot ROM [Disabled]This item allows you to enable or disable the MAC boot ROM. This itemappears only when the Onboard LAN Onboard LAN Onboard LAN Onboard LAN Onboard LAN item is set to [Enabled].Configuration options: [Disabled] [Enabled]

Onboard LAN2 [Enabled]Onboard LAN2 [Enabled]Onboard LAN2 [Enabled]Onboard LAN2 [Enabled]Onboard LAN2 [Enabled]Allows you to enable or disable the onchip MAC LAN2.Configuration options: [Disabled] [Enabled]

Onboard LAN Boot ROM2 [Disabled]This item allows you to enable or disable the MAC boot ROM2. Thisitem appears only when the Onboard LAN2 Onboard LAN2 Onboard LAN2 Onboard LAN2 Onboard LAN2 item is set to[Enabled]. Configuration options: [Disabled] [Enabled]

Onboard IEEE1394 [Enabled]Onboard IEEE1394 [Enabled]Onboard IEEE1394 [Enabled]Onboard IEEE1394 [Enabled]Onboard IEEE1394 [Enabled]Allows you to enable or disable the onboard IEEE 1394a controller.Configuration options: [Disabled] [Enabled]

Onboard Devices

HD Audio [Enabled]Onboard LAN [Enabled]

Onboard LAN Boot ROM [Disabled]Onboard Lan2 [Enabled]Onboard LAN Boot ROM2 [Disabled]Onboard IEEE1394 [Enabled]Silicon Image Mode [SATA mode]

Configure ITE8712 Super IO Chipset

Serial Port1 Address [3F8/IRQ4]Parallel Port Address [378]Parallel Port Mode [EPP+ECP]

EPP Version [1.9]ECP Mode DMA Channel [DMA3]

Parallel Port IRQ [IRQ7]

Onboard Game Port [Enabled]Onboard MIDI Port [330]

MIDI IRQ Select [IRQ5]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -314 -314 -314 -314 -31

Parallel Port Mode [EPP+ECP]Parallel Port Mode [EPP+ECP]Parallel Port Mode [EPP+ECP]Parallel Port Mode [EPP+ECP]Parallel Port Mode [EPP+ECP]Allows you to select the Parallel Port mode.Configuration options: [Normal] [EPP] [ECP] [EPP+ECP]

EPP Ve r s i on [1 .9 ]EPP Ve r s i on [1 .9 ]EPP Ve r s i on [1 .9 ]EPP Ve r s i on [1 .9 ]EPP Ve r s i on [1 .9 ]

Appears only when the Parallel Port Mode is set to [EPP] or[EPP+ECP]. Allows you to select the parallel port EPP version.Configuration options: [1.9] [1.7]

ECP Mode DMA Channe l [DMA3]ECP Mode DMA Channe l [DMA3]ECP Mode DMA Channe l [DMA3]ECP Mode DMA Channe l [DMA3]ECP Mode DMA Channe l [DMA3]

Appears only when the Parallel Port Mode is set to [EPP+ECP]or[ECP]. This item allows you to set the Parallel Port ECP DMA.Configuration options: [DMA0] [DMA1] [DMA3]

Parallel Port IRQ [IRQ7]Allows you to select the parallel port IRQ.Configuration options: [IRQ5] [IRQ7]

Onboard Game Port [Enabled]Onboard Game Port [Enabled]Onboard Game Port [Enabled]Onboard Game Port [Enabled]Onboard Game Port [Enabled]Allows you to enable or disable the onboard game port.Configuration options: [Disabled] [Enabled]

Onboard MIDI Port [330]Onboard MIDI Port [330]Onboard MIDI Port [330]Onboard MIDI Port [330]Onboard MIDI Port [330]Allows you to select the MIDI Port address or to disable the port.Configuration options: [Disabled] [300] [330]

MIDI IRQ Select [IRQ5]This item allows the BIOS to select the MIDI port IRQs.Configuration options: [IRQ5] [IRQ7] [IRQ10] [IRQ11]

Serial Port1 Address [3F8/IRQ4]Serial Port1 Address [3F8/IRQ4]Serial Port1 Address [3F8/IRQ4]Serial Port1 Address [3F8/IRQ4]Serial Port1 Address [3F8/IRQ4]Allows you to select the Serial Port1 base address.Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4][2E8/IRQ3]

Parallel Port Address [378]Parallel Port Address [378]Parallel Port Address [378]Parallel Port Address [378]Parallel Port Address [378]Allows you to select the Parallel Port base addresses.Configuration options: [Disabled] [378] [278]

Sil icon Image Mode [SATA mode]Sil icon Image Mode [SATA mode]Sil icon Image Mode [SATA mode]Sil icon Image Mode [SATA mode]Sil icon Image Mode [SATA mode]Allows you to select the Silicon Image SATA controller mode.Configuration options: [SATA mode] [RAID mode] [Disabled]

4 -324 -324 -324 -324 -32 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

4.4.54.4.54.4.54.4.54.4.5 PCI PnPPCI PnPPCI PnPPCI PnPPCI PnPThe PCI PnP menu items allow you to change the advanced settings forPCI/PnP devices. The menu includes setting IRQ and DMA channel resourcesfor either PCI/PnP or legacy ISA devices, and setting the memory size blockfor legacy ISA devices.

Advanced PCI/PnP SettingsWARNING: Setting wrong values in below sections

may cause system to malfunction.Plug And Play O/S [No]PCI Latency Timer [64]Allocate IRQ to PCI VGA [Yes]

IRQ-3 assigned to [PCI Device]IRQ-4 assigned to [PCI Device]IRQ-5 assigned to [PCI Device]IRQ-7 assigned to [PCI Device]IRQ-9 assigned to [PCI Device]IRQ-10 assigned to [PCI Device]IRQ-11 assigned to [PCI Device]IRQ-14 assigned to [PCI Device]IRQ-15 assigned to [PCI Device]

Plug And Play O/S [No]Plug And Play O/S [No]Plug And Play O/S [No]Plug And Play O/S [No]Plug And Play O/S [No]When set to [No], BIOS configures all the devices in the system. When setto [Yes] and if you install a Plug and Play operating system, the operatingsystem configures the Plug and Play devices not required for boot.Configuration options: [No] [Yes]

PCI Latency Timer [64]PCI Latency Timer [64]PCI Latency Timer [64]PCI Latency Timer [64]PCI Latency Timer [64]Allows you to select the value in units of PCI clocks for the PCI devicelatency timer register. Configuration options: [32] [64] [96] [128] [160][192] [224] [248]

Allocate IRQ to PCI VGA [Yes]Allocate IRQ to PCI VGA [Yes]Allocate IRQ to PCI VGA [Yes]Allocate IRQ to PCI VGA [Yes]Allocate IRQ to PCI VGA [Yes]When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the cardrequests for an IRQ. When set to [No], BIOS does not assign an IRQ to thePCI VGA card even if requested. Configuration options: [No] [Yes]

IRQ-xx assigned to [PCI Device]IRQ-xx assigned to [PCI Device]IRQ-xx assigned to [PCI Device]IRQ-xx assigned to [PCI Device]IRQ-xx assigned to [PCI Device]When set to [PCI Device], the specific IRQ is free for use of PCI/PnPdevices. When set to [Reserved], the IRQ is reserved for legacy ISAdevices. Configuration options: [PCI Device] [Reserved]

Take caution when changing the settings of the PCI PnP menu items.Incorrect field values can cause the system to malfunction.

NO: lets the BIOSconfigue all thedevices in the system.YES: lets theoperating systemconfigure Plug andPlay (PnP) devices notrequired for boot ifyour system has a Plugand Play operatingsystem.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -334 -334 -334 -334 -33

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

4.4.74.4.74.4.74.4.74.4.7 USB ConfigurationUSB ConfigurationUSB ConfigurationUSB ConfigurationUSB ConfigurationThe items in this menu allows you to change the USB-related features.Select an item then press <Enter> to display the configuration options.

The Modu le Vers ionModu le Vers ionModu le Vers ionModu le Vers ionModu le Vers ion and USB Dev ices Enab led USB Dev ices Enab led USB Dev ices Enab led USB Dev ices Enab led USB Dev ices Enab led items show theauto-detected values. If no USB device is detected, the item showsN o n eN o n eN o n eN o n eN o n e.

USB Configuration

Module Version - 2.24.0-10.4

USB Devices Enabled: None

USB Controller [USB1.1+2.0]Legacy USB Support [Auto]USB 2.0 Controller Mode [HiSpeed]BIOS EHCI Hand-off [Enabled]

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYAdvanced

4.4.64.4.64.4.64.4.64.4.6 LAN Cable StatusLAN Cable StatusLAN Cable StatusLAN Cable StatusLAN Cable StatusThis menu displays the status of the Local Area Network (LAN) cableconnected to the LAN (RJ-45) port.

POST Check LAN Cable [Disabled]POST Check LAN Cable [Disabled]POST Check LAN Cable [Disabled]POST Check LAN Cable [Disabled]POST Check LAN Cable [Disabled]Allows you to enable or disable LAN cable check during POST. Whenenabled, the menu reports the cable faults or shorts, and displays the point(length) where the fault or short is detected. Configuration options:[Disabled] [Enabled]

POST Check LAN Cable [Disabled]

LAN Cable StatusPair Status Length

1-2 Open 0.0M3-6 Open 0.0M4-5 Open 0.0M7-8 Open 0.0M

Check LAN cableduring POST.

4 -344 -344 -344 -344 -34 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

USB Controller [USB1.1+2.0]USB Controller [USB1.1+2.0]USB Controller [USB1.1+2.0]USB Controller [USB1.1+2.0]USB Controller [USB1.1+2.0]Allows you to disable the USB controllers, or choose which controller toenable. Configuration options: [Disabled ] [USB1.1 Only] [USB1.1+2.0]

Legacy USB Support [Auto]Legacy USB Support [Auto]Legacy USB Support [Auto]Legacy USB Support [Auto]Legacy USB Support [Auto]Allows you to enable or disable support for legacy USB devices. Setting to[Auto] allows the system to detect the presence of USB devices atstartup. If detected, the USB controller legacy mode is enabled. If no USBdevice is detected, the legacy USB support is disabled.Configuration options: [Disabled] [Enabled] [Auto]

USB 2.0 Controller Mode [HiSpeed]USB 2.0 Controller Mode [HiSpeed]USB 2.0 Controller Mode [HiSpeed]USB 2.0 Controller Mode [HiSpeed]USB 2.0 Controller Mode [HiSpeed]Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) orFullSpeed (12 Mbps). Configuration options: [FullSpeed] [HiSpeed]

BIOS EHCI Hand-off [Enabled]BIOS EHCI Hand-off [Enabled]BIOS EHCI Hand-off [Enabled]BIOS EHCI Hand-off [Enabled]BIOS EHCI Hand-off [Enabled]Allows you to enable support for operating systems without an EHCIhand-off feature. Configuration options: [Disabled] [Enabled]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -354 -354 -354 -354 -35

Select Screen Select Item

+- Change FieldF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain Advanced Power Boot Exit

4.5 Power menuThe Power menu items allow you to change the settings for the ACPI andAdvanced Power Management (APM) features. Select an item then press<Enter> to display the configuration options.

4.5.14.5.14.5.14.5.14.5.1 Suspend Mode [Auto]Suspend Mode [Auto]Suspend Mode [Auto]Suspend Mode [Auto]Suspend Mode [Auto]Allows you to select the Advanced Configuration and Power Interface (ACPI)state to be used for system suspend. Setting this item to [Auto] allows theOS to select the ACPI state. Configuration options: [S1 (POS) Only][S3 Only] [Auto]

4.5.24.5.24.5.24.5.24.5.2 Repost Video on S3 Resume [No]Repost Video on S3 Resume [No]Repost Video on S3 Resume [No]Repost Video on S3 Resume [No]Repost Video on S3 Resume [No]Determines whether to invoke VGA BIOS POST on S3/STR resume.Configuration options: [No] [Yes]

4.5.34.5.34.5.34.5.34.5.3 ACPI 2.0 Support [No]ACPI 2.0 Support [No]ACPI 2.0 Support [No]ACPI 2.0 Support [No]ACPI 2.0 Support [No]Allows you to add more tables for Advanced Configuration and PowerInterface (ACPI) 2.0 specifications. Configuration options: [No] [Yes]

4.5.44.5.44.5.44.5.44.5.4 ACPI APIC Support [Enabled]ACPI APIC Support [Enabled]ACPI APIC Support [Enabled]ACPI APIC Support [Enabled]ACPI APIC Support [Enabled]Allows you to enable or disable the Advanced Configuration and PowerInterface (ACPI) support in the Advanced Programmable InterruptController (APIC). When set to Enabled, the ACPI APIC table pointer isincluded in the RSDT pointer list. Configuration options: [Disabled][Enabled]

Suspend Mode [Auto]Repost Video on S3 Resume [No]ACPI 2.0 Support [No]ACPI APIC Support [Enabled]

APM ConfigurationHardware Monitor

4 -364 -364 -364 -364 -36 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYPower

4.5.54.5.54.5.54.5.54.5.5 APM ConfigurationAPM ConfigurationAPM ConfigurationAPM ConfigurationAPM Configuration

Power Button Mode [On/Off]Power Button Mode [On/Off]Power Button Mode [On/Off]Power Button Mode [On/Off]Power Button Mode [On/Off]Allows the system to go into On/Off mode or suspend mode when thepower button is pressed. Configuration options: [On/Off] [Suspend]

Restore on AC Power Loss [Power Off]Restore on AC Power Loss [Power Off]Restore on AC Power Loss [Power Off]Restore on AC Power Loss [Power Off]Restore on AC Power Loss [Power Off]When set to Power Off, the system goes into off state after an AC powerloss. When set to Power On, the system goes on after an AC power loss.When set to Last State, the system goes into either off or on state,whatever the system state was before the AC power loss.Configuration options: [Power Off] [Power On] [Last State]

Power On By PS/2 Keyboard [Disabled]Power On By PS/2 Keyboard [Disabled]Power On By PS/2 Keyboard [Disabled]Power On By PS/2 Keyboard [Disabled]Power On By PS/2 Keyboard [Disabled]Allows you to use specific keys on the keyboard to turn on the system.This feature requires an ATX power supply that provides at least 1A on the+5VSB lead. Configuration options: [Disabled] [Enabled]

Power On By PS/2 Mouse [Disabled]Power On By PS/2 Mouse [Disabled]Power On By PS/2 Mouse [Disabled]Power On By PS/2 Mouse [Disabled]Power On By PS/2 Mouse [Disabled]When set to [Enabled], this parameter allows you to use the PS/2 mouseto turn on the system. This feature requires an ATX power supply thatprovides at least 1A on the +5VSB lead. Configuration options: [Disabled][Enabled]

Power On By RTC Alarm [Disabled]Power On By RTC Alarm [Disabled]Power On By RTC Alarm [Disabled]Power On By RTC Alarm [Disabled]Power On By RTC Alarm [Disabled]Allows you to enable or disable RTC to generate a wake event.Configuration options: [Disabled] [Enabled]

Power Button Mode [On/Off]

Restore on AC Power Loss [Power Off]Power On By PS/2 Keyboard [Disabled]Power On By PS/2 Mouse [Disabled]Power On By RTC Alarm [Disabled]Power On By External Modems [Disabled]Power On By PCI/PCI-Ex Devices [Disabled]

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -374 -374 -374 -374 -37

The succeeding items appear when the Power On By RTC A la rmPower On By RTC A la rmPower On By RTC A la rmPower On By RTC A la rmPower On By RTC A la rmitem is set to Enabled.

RTC Alarm Date (Days) [Every Day]RTC Alarm Date (Days) [Every Day]RTC Alarm Date (Days) [Every Day]RTC Alarm Date (Days) [Every Day]RTC Alarm Date (Days) [Every Day]To set the alarm date, highlight this item and press the <+> or <-> key tomake the selection.

RTC Alarm Hour (Hours) [0]RTC Alarm Hour (Hours) [0]RTC Alarm Hour (Hours) [0]RTC Alarm Hour (Hours) [0]RTC Alarm Hour (Hours) [0]To set the alarm hour, highlight this item and press the <+> or <-> key tomake the selection.

RTC Alarm Minute (Minutes) [0]RTC Alarm Minute (Minutes) [0]RTC Alarm Minute (Minutes) [0]RTC Alarm Minute (Minutes) [0]RTC Alarm Minute (Minutes) [0]To set the alarm minute, highlight this item and press the <+> or <-> keyto make the selection.

RTC Alarm Second (Seconds) [0]RTC Alarm Second (Seconds) [0]RTC Alarm Second (Seconds) [0]RTC Alarm Second (Seconds) [0]RTC Alarm Second (Seconds) [0]To set the alarm second, highlight this item and press the <+> or <-> keyto make the selection.

Power On By External Modems [Disabled]Power On By External Modems [Disabled]Power On By External Modems [Disabled]Power On By External Modems [Disabled]Power On By External Modems [Disabled]Allows either settings of [Enabled] or [Disabled] for powering up thecomputer when the external modem receives a call while the computer is inSoft-off mode. Configuration options: [Disabled] [Enabled]

The computer cannot receive or transmit data until the computer andapplications are fully running. Thus, connection cannot be made on thefirst try. Turning an external modem off and then back on while thecomputer is off causes an initialization string that turns the systempower on.

Power On By PCI/PCI-Ex Devices [Disabled]Power On By PCI/PCI-Ex Devices [Disabled]Power On By PCI/PCI-Ex Devices [Disabled]Power On By PCI/PCI-Ex Devices [Disabled]Power On By PCI/PCI-Ex Devices [Disabled]When set to [Enabled], this parameter allows you to turn on the systemthrough a PCI LAN or modem card. This feature requires an ATX powersupply that provides at least 1A on the +5VSB lead.Configuration options: [Disabled] [Enabled]

4 -384 -384 -384 -384 -38 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYPower

4.5.64.5.64.5.64.5.64.5.6 Hardware MonitorHardware MonitorHardware MonitorHardware MonitorHardware Monitor

Hardware MonitorCPU Temperature [32.5ºC/90.5ºF]MB Temperature [36.0ºC/96.5ºF]

CPU Fan Speed [3813 RPM]Chassis Fan Speed [N/A]Power Fan Speed [N/A]

VCORE Voltage [ 1.320V]3.3V Voltage [ 3.345V]5V Voltage [ 5.094V]12V Voltage [11.880V]

CPU QFan Control [Disabled]

Chassis QFan Control [Disabled]

CPU Temperature [xxxºC/xxxºF]CPU Temperature [xxxºC/xxxºF]CPU Temperature [xxxºC/xxxºF]CPU Temperature [xxxºC/xxxºF]CPU Temperature [xxxºC/xxxºF]MB Temperature [xxxºC/xxxºF]MB Temperature [xxxºC/xxxºF]MB Temperature [xxxºC/xxxºF]MB Temperature [xxxºC/xxxºF]MB Temperature [xxxºC/xxxºF]The onboard hardware monitor automatically detects and displays themotherboard and CPU temperatures. Select [Ignored] if you do not wish todisplay the detected temperatures.

CPU Fan Speed [xxxxRPM] or [Ignored]CPU Fan Speed [xxxxRPM] or [Ignored]CPU Fan Speed [xxxxRPM] or [Ignored]CPU Fan Speed [xxxxRPM] or [Ignored]CPU Fan Speed [xxxxRPM] or [Ignored]The onboard hardware monitor automatically detects and displays the CPUfan speed in rotations per minute (RPM). If the fan is not connected to themotherboard, the field shows N/A. Select [Ignore] from the item options todisable CPU fan speed monitoring.

Chassis Fan Speed N/A] or [Ignored]Chassis Fan Speed N/A] or [Ignored]Chassis Fan Speed N/A] or [Ignored]Chassis Fan Speed N/A] or [Ignored]Chassis Fan Speed N/A] or [Ignored]The onboard hardware monitor automatically detects and displays thechassis fan speed in rotations per minute (RPM). If the fan is not connectedto the chassis, the specific field shows N/A. Select [Ignore] from the itemoptions to disable chassis fan speed monitoring.

Power Fan Speed [N/A] or [Ignored]Power Fan Speed [N/A] or [Ignored]Power Fan Speed [N/A] or [Ignored]Power Fan Speed [N/A] or [Ignored]Power Fan Speed [N/A] or [Ignored]The onboard hardware monitor automatically detects and displays thepower fan speed in rotations per minute (RPM). If the fan is not connectedto the power fan connector, the specific field shows N/A.

VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V VoltageVCORE Voltage, 3.3V Voltage, 5V Voltage, 12V VoltageVCORE Voltage, 3.3V Voltage, 5V Voltage, 12V VoltageVCORE Voltage, 3.3V Voltage, 5V Voltage, 12V VoltageVCORE Voltage, 3.3V Voltage, 5V Voltage, 12V VoltageThe onboard hardware monitor automatically detects the voltage outputthrough the onboard voltage regulators.

CPU Temperature

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -394 -394 -394 -394 -39

CPU QFan Control [Disabled]CPU QFan Control [Disabled]CPU QFan Control [Disabled]CPU QFan Control [Disabled]CPU QFan Control [Disabled]Allows you to enable or disable the ASUS Q-Fan feature that smartlyadjusts the fan speeds for more efficient system operation. Configurationoptions: [Disabled] [Enabled]

The following items appear when the CPU QFan Contro l CPU QFan Contro l CPU QFan Contro l CPU QFan Contro l CPU QFan Contro l item is setto [Enabled].

CPUFan Start Temperature [5]CPUFan Start Temperature [5]CPUFan Start Temperature [5]CPUFan Start Temperature [5]CPUFan Start Temperature [5]Allows you to set the CPU temperature at which the CPU fan starts. Usethe <+>/<-> key or use the numeric keypad to set the value. Valid valuesrange from [0] to [100].

CPUFan Full-speed Temperature5 [45]CPUFan Full-speed Temperature5 [45]CPUFan Full-speed Temperature5 [45]CPUFan Full-speed Temperature5 [45]CPUFan Full-speed Temperature5 [45]Allows you to set the CPU temperature at which the CPU fan runs at fullspeed. Use the <+>/<-> key or use the numeric keypad to set the value.Valid values range from [0] to [100].

CPUFan Start CPUFan Start CPUFan Start CPUFan Start CPUFan Start PWM PWM PWM PWM PWM [55][55][55][55][55]Allows you to set the CPU temperature at which the power managementfeature starts. Use the <+>/<-> key or use the numeric keypad to set thevalue. Valid values range from [0] to [100].

Chassis QFan Control [Disabled]Chassis QFan Control [Disabled]Chassis QFan Control [Disabled]Chassis QFan Control [Disabled]Chassis QFan Control [Disabled]Allows you to enable or disable the ASUS Q-Fan feature that smartlyadjusts the fan speeds for more efficient system operation. Configurationoptions: [Disabled] [Enabled]

The following items appear when the Chass is QFan Contro l Chass is QFan Contro l Chass is QFan Contro l Chass is QFan Contro l Chass is QFan Contro l item isset to [Enabled].

ChassisFan Off Temperature [0]ChassisFan Off Temperature [0]ChassisFan Off Temperature [0]ChassisFan Off Temperature [0]ChassisFan Off Temperature [0]Allows you to specify the maximum chassis temperature at which thesystem will shut down. Use the <+>/<-> key or use the numeric keypad toset the value. Valid values range from [0] to [100].

ChassisFan Start Temperature [25]ChassisFan Start Temperature [25]ChassisFan Start Temperature [25]ChassisFan Start Temperature [25]ChassisFan Start Temperature [25]Allows you to set the chassis temperature at which the CPU fan starts. Usethe <+>/<-> key or use the numeric keypad to set the value. Valid valuesrange from [0] to [100].

4 -404 -404 -404 -404 -40 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

ChassisFan Full-speed Temperature[45]ChassisFan Full-speed Temperature[45]ChassisFan Full-speed Temperature[45]ChassisFan Full-speed Temperature[45]ChassisFan Full-speed Temperature[45]Allows you to set the CPU temperature at which the chassis fan runs at fullspeed. Use the <+>/<-> key or use the numeric keypad to set the value.Valid values range from [0] to [100].

ChassisFan Start ChassisFan Start ChassisFan Start ChassisFan Start ChassisFan Start PWM PWM PWM PWM PWM [40][40][40][40][40]Allows you to set the chassis temperature at which the power managementfeature starts. Use the <+>/<-> key or use the numeric keypad to set thevalue. Valid values range from [0] to [100].

4.6 Boot menuThe Boot menu items allow you to change the system boot options. Selectan item then press <Enter> to display the sub-menu.

Select Screen Select Item

Enter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain Advanced Power Boot Exit

Boot Settings

Boot Device Priority

Boot Settings ConfigurationSecurity

Specifies the BootDevice Boot Prioritysequence.

A virtual floppy diskdrive (Floppy DriveB:) may appear whenyou set the CD-ROMdrive as the firstboot device.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -414 -414 -414 -414 -41

4.6.14.6.14.6.14.6.14.6.1 Boot Device PriorityBoot Device PriorityBoot Device PriorityBoot Device PriorityBoot Device Priority

1st ~ xxth Boot Device [1st Floppy Drive]1st ~ xxth Boot Device [1st Floppy Drive]1st ~ xxth Boot Device [1st Floppy Drive]1st ~ xxth Boot Device [1st Floppy Drive]1st ~ xxth Boot Device [1st Floppy Drive]These items specify the boot device priority sequence from the availabledevices. The number of device items that appears on the screen dependson the number of devices installed in the system.Configuration options: [xxxxx Drive] [Disabled]

The following item appears only when you have set a Serial ATA drive ina RAID configuration as boot device.

Hard Disk [XXX Drive]Hard Disk [XXX Drive]Hard Disk [XXX Drive]Hard Disk [XXX Drive]Hard Disk [XXX Drive]This item specifies the Serial ATA boot device priority sequence from theavailable devices in a RAID configuration.Configuration options: [xxxxx Drive] [Disabled]

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYBoot

Boot Device Priority

1st Boot Device [1st FLOPPY DRIVE]2nd Boot Device [PM-ST320410A]3rd Boot Device [PS-ASUS CD-S520/A]

Specifies the bootsequence from theavailabe devices.

A device enclosed inparenthesis has beendisabled in thecorresponding menu.

4 -424 -424 -424 -424 -42 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Quick Boot [Enabled]Quick Boot [Enabled]Quick Boot [Enabled]Quick Boot [Enabled]Quick Boot [Enabled]Enabling this item allows the BIOS to skip some power on self tests (POST)while booting to decrease the time needed to boot the system. When setto [Disabled], BIOS performs all the POST items.Configuration options: [Disabled] [Enabled]

Full Screen Logo [Enabled]Full Screen Logo [Enabled]Full Screen Logo [Enabled]Full Screen Logo [Enabled]Full Screen Logo [Enabled]Allows you to enable or disable the full screen logo display feature.Configuration options: [Disabled] [Enabled]

When this item is set to [Disabled], the system displays normal POSTmessages; when this item is set to [Enabled], the system displays OEMLogo instead of POST messages.

AddOn ROM Display Mode [Force BIOS]AddOn ROM Display Mode [Force BIOS]AddOn ROM Display Mode [Force BIOS]AddOn ROM Display Mode [Force BIOS]AddOn ROM Display Mode [Force BIOS]Sets the display mode for option ROM.Configuration options: [Force BIOS] [Keep Current]

Bootup Num-Lock [On]Bootup Num-Lock [On]Bootup Num-Lock [On]Bootup Num-Lock [On]Bootup Num-Lock [On]Allows you to select the power-on state for the NumLock.Configuration options: [Off] [On]

PS/2 Mouse Support [Auto]PS/2 Mouse Support [Auto]PS/2 Mouse Support [Auto]PS/2 Mouse Support [Auto]PS/2 Mouse Support [Auto]Allows you to enable or disable support for PS/2 mouse.Configuration options: [Disabled] [Enabled] [Auto]

4.6.24.6.24.6.24.6.24.6.2 Boot Settings ConfigurationBoot Settings ConfigurationBoot Settings ConfigurationBoot Settings ConfigurationBoot Settings Configuration

Select Screen Select Item

+- Change OptionF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYBoot

Boot Settings Configuration

Quick Boot [Enabled]Full Screen Logo [Disabled]AddOn ROM Display Mode [Force BIOS]Bootup Num-Lock [On]PS/2 Mouse Support [Auto]System Keyboard [Present]Wait for ‘F1’ if Error [Enabled]Hit ‘DEL’ Message Display [Enabled]Interrupt 19 Capture [Disabled]

Allows BIOS to skipcertain tests whilebooting. This willdecrease the timeneeded to boot thesystem.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -434 -434 -434 -434 -43

Hit ‘DEL’ Message Display [Enabled]Hit ‘DEL’ Message Display [Enabled]Hit ‘DEL’ Message Display [Enabled]Hit ‘DEL’ Message Display [Enabled]Hit ‘DEL’ Message Display [Enabled]When set to Enabled, the system displays the message “Press DEL to runSetup” during POST. Configuration options: [Disabled] [Enabled]

Interrupt 19 Capture [Disabled]Interrupt 19 Capture [Disabled]Interrupt 19 Capture [Disabled]Interrupt 19 Capture [Disabled]Interrupt 19 Capture [Disabled]When set to [Enabled], this function allows the option ROMs to trapInterrupt 19. Configuration options: [Disabled] [Enabled]

4.6.34.6.34.6.34.6.34.6.3 SecuritySecuritySecuritySecuritySecurityThe Security menu items allow you to change the system security settings.Select an item then press <Enter> to display the configuration options.

Change Supervisor PasswordChange Supervisor PasswordChange Supervisor PasswordChange Supervisor PasswordChange Supervisor PasswordSelect this item to set or change the supervisor password. The SupervisorPassword item on top of the screen shows the default Not Insta l ledNot Insta l ledNot Insta l ledNot Insta l ledNot Insta l led.After you set a password, this item shows Insta l ledInsta l ledInsta l ledInsta l ledInsta l led.

To set a Supervisor Password:

1. Select the Change Supervisor Password item and press <Enter>.2. From the password box, type a password composed of at least six

letters and/or numbers, then press <Enter>.3. Confirm the password when prompted.

Select Screen Select Item

Enter ChangeF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYBoot

Security Settings

Supervisor Password : Not InstalledUser Password : Not Installed

Change Supervisor PasswordChange User password

<Enter> to changepassword.<Enter> again todisabled password.

Wait For ‘F1’ If Error [Enabled]Wait For ‘F1’ If Error [Enabled]Wait For ‘F1’ If Error [Enabled]Wait For ‘F1’ If Error [Enabled]Wait For ‘F1’ If Error [Enabled]When set to Enabled, the system waits for the F1 key to be pressed whenerror occurs. Configuration options: [Disabled] [Enabled]

4 -444 -444 -444 -444 -44 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

User Access Level [Full Access]User Access Level [Full Access]User Access Level [Full Access]User Access Level [Full Access]User Access Level [Full Access]This item allows you to select the access restriction to the Setup items.Configuration options: [No Access] [View Only] [Limited] [Full Access]

No AccessNo AccessNo AccessNo AccessNo Access prevents user access to the Setup utility.

V iew Only V iew Only V iew Only V iew Only V iew Only allows access but does not allow change to any field.

L imited L imited L imited L imited L imited allows changes only to selected fields, such as Date andTime.

Fu l l AccessFu l l AccessFu l l AccessFu l l AccessFu l l Access allows viewing and changing all the fields in the Setuputility.

Change User PasswordChange User PasswordChange User PasswordChange User PasswordChange User PasswordSelect this item to set or change the user password. The User Passworditem on top of the screen shows the default Not Insta l ledNot Insta l ledNot Insta l ledNot Insta l ledNot Insta l led. After you seta password, this item shows Insta l ledInsta l ledInsta l ledInsta l ledInsta l led.

Select Screen Select Item

Enter ChangeF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYBoot

Security Settings

Supervisor Password : InstalledUser Password : Not Installed

Change Supervisor PasswordUser Access Level [Full Access]Change User PasswordClear User PasswordPassword Check [Setup]

<Enter> to changepassword.<Enter> again todisabled password.

To clear the supervisor password, select the Change Supervisor Passwordthen press <Enter>. The message “Password Uninstalled” appears.

If you forget your BIOS password, you can clear it by erasing the CMOSReal Time Clock (RTC) RAM. See section “2.6 Jumpers” for informationon how to erase the RTC RAM.

After you have set a supervisor password, the other items appear to allowyou to change other security settings.

The message “Password Installed” appears after you successfully set yourpassword.

To change the supervisor password, follow the same steps as in setting auser password.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 4 -454 -454 -454 -454 -45

To set a User Password:

1. Select the Change User Password item and press <Enter>.2. On the password box that appears, type a password composed of at

least six letters and/or numbers, then press <Enter>.3. Confirm the password when prompted.

The message “Password Installed” appears after you set your passwordsuccessfully.

To change the user password, follow the same steps as in setting a userpassword.

Password Check [Setup]Password Check [Setup]Password Check [Setup]Password Check [Setup]Password Check [Setup]When set to [Setup], BIOS checks for user password when accessing theSetup utility. When set to [Always], BIOS checks for user password bothwhen accessing Setup and booting the system.Configuration options: [Setup] [Always]

4.7 Exit menu

Pressing <Esc> does not immediately exit this menu. Select one of theoptions from this menu or <F10> from the legend bar to exit.

The Exit menu items allow you to load the optimal or failsafe default valuesfor the BIOS items, and save or discard your changes to the BIOS items.

Select Screen Select Item

Enter Go to Sub ScreenF1 General HelpF10 Save and ExitESC Exit

BIOS SETUP UTILITYMain Advanced Power Boot Exit

Exit Options

Exit & Save ChangesExit & Discard ChangesDiscard Changes

Load Setup Defaults

Exit system setupafter saving thechanges.F10 key can be usedfor this operation.

4 -464 -464 -464 -464 -46 Chapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setupChapter 4 : B IOS setup

Exit & Discard ChangesExit & Discard ChangesExit & Discard ChangesExit & Discard ChangesExit & Discard ChangesSelect this option only if you do not want to save the changes that youmade to the Setup program. If you made changes to fields other thanSystem Date, System Time, and Password, the BIOS asks for a confirmationbefore exiting.

Discard ChangesDiscard ChangesDiscard ChangesDiscard ChangesDiscard ChangesThis option allows you to discard the selections you made and restore thepreviously saved values. After selecting this option, a confirmation appears.Select [Ok][Ok][Ok][Ok][Ok] to discard any changes and load the previously saved values.

Load Setup DefaultsLoad Setup DefaultsLoad Setup DefaultsLoad Setup DefaultsLoad Setup DefaultsThis option allows you to load the default values for each of theparameters on the Setup menus. When you select this option or if youpress <F5>, a confirmation window appears. Select [Ok][Ok][Ok][Ok][Ok] to load defaultvalues. Select Ex it & Save ChangesEx it & Save ChangesEx it & Save ChangesEx it & Save ChangesEx it & Save Changes or make other changes beforesaving the values to the non-volatile RAM.

If you attempt to exit the Setup program without saving your changes,the program prompts you with a message asking if you want to saveyour changes before exiting. Press <Enter> to save the changes whileexiting.

Exit & Save ChangesExit & Save ChangesExit & Save ChangesExit & Save ChangesExit & Save ChangesOnce you are finished making your selections, choose this option from theExit menu to ensure the values you selected are saved to the CMOS RAM.An onboard backup battery sustains the CMOS RAM so it stays on evenwhen the PC is turned off. When you select this option, a confirmationwindow appears. Select [Ok][Ok][Ok][Ok][Ok] to save changes and exit.

5Softwaresupport

This chapter describes the contentsof the support CD that comes withthe motherboard package.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE

Chapter summary 55.1 Installing an operating system ............................................. 5-15.2 Support CD information ........................................................ 5-15.3 Software information ......................................................... 5-105.4 RAID configurations ............................................................ 5-265.5 Creating a RAID driver disk ................................................. 5-42

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 - 15 - 15 - 15 - 15 - 1

If Auto run Auto run Auto run Auto run Auto run is NOT enabled in your computer, browse the contents ofthe support CD to locate the file ASSETUP.EXE from the BIN folder.Double-click the ASSETUP .EXEASSETUP .EXEASSETUP .EXEASSETUP .EXEASSETUP .EXE to run the CD.

C l i c k an i t em to i n s ta l lC l i c k an i t em to i n s ta l lC l i c k an i t em to i n s ta l lC l i c k an i t em to i n s ta l lC l i c k an i t em to i n s ta l l

5.1 Installing an operating systemThis motherboard supports Windows® 2000/XP operating systems (OS).Always install the latest OS version and corresponding updates to maximizethe features of your hardware.

5.2 Support CD informationThe support CD that came with the motherboard package contains thedrivers, software applications, and utilities that you can install to avail allmotherboard features.

5.2.15.2.15.2.15.2.15.2.1 Running the support CDRunning the support CDRunning the support CDRunning the support CDRunning the support CDPlace the support CD to the optical drive. The CD automatically displays theDr ivers Dr ivers Dr ivers Dr ivers Dr ivers menu if Autorun is enabled in your computer.

• Motherboard settings and hardware options vary. Use the setupprocedures presented in this chapter for reference only. Refer toyour OS documentation for detailed information.

• Make sure that you install Windows® 2000 Service Pack 4 or theWindows® XP Service Pack 1 or later versions before installing thedrivers for better compatibility and system stability.

The contents of the support CD are subject to change at any timewithout notice. Visit the ASUS website(www.asus.com) for updates.

C l i c k an i con toC l i c k an i con toC l i c k an i con toC l i c k an i con toC l i c k an i con tod i sp l ay suppo r td i sp l ay suppo r td i sp l ay suppo r td i sp l ay suppo r td i sp l ay suppo r tCD/mothe rboa rdCD/mothe rboa rdCD/mothe rboa rdCD/mothe rboa rdCD/mothe rboa rdi n f o rmat i oni n f o rmat i oni n f o rmat i oni n f o rmat i oni n f o rmat i on

5 - 25 - 25 - 25 - 25 - 2 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.2.25.2.25.2.25.2.25.2.2 Drivers menuDrivers menuDrivers menuDrivers menuDrivers menuThe drivers menu shows the available device drivers if the system detectsinstalled devices. Install the necessary drivers to activate the devices.

AMD Cool ‘n’ Quiet DriverAMD Cool ‘n’ Quiet DriverAMD Cool ‘n’ Quiet DriverAMD Cool ‘n’ Quiet DriverAMD Cool ‘n’ Quiet DriverInstalls the AMD Cool ‘n’ Quiet™ driver.

Marvell Yukon Gigabit Ethernet DriverMarvell Yukon Gigabit Ethernet DriverMarvell Yukon Gigabit Ethernet DriverMarvell Yukon Gigabit Ethernet DriverMarvell Yukon Gigabit Ethernet DriverInstalls the Marvell® Yukon™ Gigabit Ethernet driver.

Si l icon Image SATA DriverSil icon Image SATA DriverSil icon Image SATA DriverSil icon Image SATA DriverSil icon Image SATA DriverInstalls the Silicon Image® Serial ATA driver.

USB 2.0 DriverUSB 2.0 DriverUSB 2.0 DriverUSB 2.0 DriverUSB 2.0 DriverInstalls the USB 2.0 driver.

The screen display and drivers option may not be the same for differentoperating system versions.

ASUS InstAll - Installation Wizard for DriversASUS InstAll - Installation Wizard for DriversASUS InstAll - Installation Wizard for DriversASUS InstAll - Installation Wizard for DriversASUS InstAll - Installation Wizard for DriversLaunches the ASUS InstallAll driver installation wizard.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 - 35 - 35 - 35 - 35 - 3

• In the AHCI mode, make sure that you install the RAID driver beforeyour connect the ULi M1575 controller.

• After you install the RAID driver, the drivers menu shows the item“UL i M1575 RAID Dr iverUL i M1575 RAID Dr iverUL i M1575 RAID Dr iverUL i M1575 RAID Dr iverUL i M1575 RAID Dr iver”.

5 - 45 - 45 - 45 - 45 - 4 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.2.35.2.35.2.35.2.35.2.3 Utilities menuUtilities menuUtilities menuUtilities menuUtilities menuThe Utilities menu shows the applications and other software that themotherboard supports.

ASUS InstAll - Installation Wizard for Util itiesASUS InstAll - Installation Wizard for Util itiesASUS InstAll - Installation Wizard for Util itiesASUS InstAll - Installation Wizard for Util itiesASUS InstAll - Installation Wizard for Util itiesLaunches the ASUS InstallAll utilities installation wizard.

Marvell Yukon VCT ApplicationMarvell Yukon VCT ApplicationMarvell Yukon VCT ApplicationMarvell Yukon VCT ApplicationMarvell Yukon VCT ApplicationThe Virtual Cable Tester (VCT) is a cable diagnostic application thatanalyzes and reports LAN cable faults and shorts.

ASUS PC Probe I IASUS PC Probe I IASUS PC Probe I IASUS PC Probe I IASUS PC Probe I IThis smart utility monitors the fan speed, CPU temperature, and systemvoltages, and alerts you of any detected problems. This utility helps youkeep your computer in healthy operating condition.

ASUS UpdateASUS UpdateASUS UpdateASUS UpdateASUS UpdateThe ASUS Update utility that allows you to update the motherboard BIOS inWindows® environment. This utility requires an Internet connection eitherthrough a network or an Internet Service Provider (ISP). See section “4.1.1ASUS Update utility” for details.

Before using the ASUS Update, make sure that you have an Internetconnection so you can connect to the ASUS website.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 - 55 - 55 - 55 - 55 - 5

ASUS Screen SaverASUS Screen SaverASUS Screen SaverASUS Screen SaverASUS Screen SaverBring life to your computer screen by installing the ASUS Screen Saver.

Adobe Acrobat Reader V7.0Adobe Acrobat Reader V7.0Adobe Acrobat Reader V7.0Adobe Acrobat Reader V7.0Adobe Acrobat Reader V7.0Installs the Adobe® Acrobat® Reader that allows you to open, view, andprint documents in Portable Document Format (PDF).

Microsoft DirectX 9.0cMicrosoft DirectX 9.0cMicrosoft DirectX 9.0cMicrosoft DirectX 9.0cMicrosoft DirectX 9.0cInstalls the Microsoft® DirectX® 9.0c driver. The Microsoft® DirectX® 9.0cis a multimedia technology that enhances computer graphics and sound.DirectX® improves the multimedia features of your computer so you canenjoy watching TV and movies, capturing videos, or playing games on yourcomputer. Visit the Microsoft® website (www.microsoft.com) for updates.

ASUS Cool ‘n’ Quiet Util ityASUS Cool ‘n’ Quiet Util ityASUS Cool ‘n’ Quiet Util ityASUS Cool ‘n’ Quiet Util ityASUS Cool ‘n’ Quiet Util ityInstalls the AMD Cool ‘n’ Quiet™ software.

Anti-virus uti l ityAnti-virus uti l ityAnti-virus uti l ityAnti-virus uti l ityAnti-virus uti l ityThe anti-virus application scans, identifies, and removes computer viruses.View the online help for detailed information.

The screen display and utilities option may not be the same for differentoperating system versions.

5 - 65 - 65 - 65 - 65 - 6 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.2.45.2.45.2.45.2.45.2.4 Make Disk menuMake Disk menuMake Disk menuMake Disk menuMake Disk menuThe Make Disk menu contains the item needed to create the ULI SerialATA/RAID driver disk.

Make ULi 32/64 bit SATA Driver DiskMake ULi 32/64 bit SATA Driver DiskMake ULi 32/64 bit SATA Driver DiskMake ULi 32/64 bit SATA Driver DiskMake ULi 32/64 bit SATA Driver DiskAllows you to create the ULI SATA driver disk for a 32/64-bit system.

Make Sil icon Image 32 bit RAID DriverMake Sil icon Image 32 bit RAID DriverMake Sil icon Image 32 bit RAID DriverMake Sil icon Image 32 bit RAID DriverMake Sil icon Image 32 bit RAID DriverMake Sil icon Image 32 bit SATA DriverMake Sil icon Image 32 bit SATA DriverMake Sil icon Image 32 bit SATA DriverMake Sil icon Image 32 bit SATA DriverMake Sil icon Image 32 bit SATA DriverAllows you to create a Silicon Image® RAID/Serial ATA driver disk for a32-bit system.

Make Sil icon Image 64 bit RAID DriverMake Sil icon Image 64 bit RAID DriverMake Sil icon Image 64 bit RAID DriverMake Sil icon Image 64 bit RAID DriverMake Sil icon Image 64 bit RAID DriverMake Sil icon Image 64 bit SATA DriverMake Sil icon Image 64 bit SATA DriverMake Sil icon Image 64 bit SATA DriverMake Sil icon Image 64 bit SATA DriverMake Sil icon Image 64 bit SATA DriverAllows you to create a Silicon Image® RAID/Serial ATA driver disk for a64-bit system.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 - 75 - 75 - 75 - 75 - 7

5.2.55.2.55.2.55.2.55.2.5 Manuals menuManuals menuManuals menuManuals menuManuals menuThe Manuals menu contains a list of supplementary user manuals. Click anitem to open the folder of the user manual.

Most user manual files are in Portable Document Format (PDF). Installthe Adobe® Acrobat® Reader from the Ut i l i t i es menuUt i l i t i es menuUt i l i t i es menuUt i l i t i es menuUt i l i t i es menu before openinga user manual file.

Si l 3132 User GuideSil 3132 User GuideSil 3132 User GuideSil 3132 User GuideSil 3132 User GuideAllows you to open the Silicon image Sil3132 SATA RAID user guide.

ULi SATA/RAID User’s ManualULi SATA/RAID User’s ManualULi SATA/RAID User’s ManualULi SATA/RAID User’s ManualULi SATA/RAID User’s ManualAllows you to open the ULi Serial ATA/RAID user’s manual.

RTL8187 Wireless LAN User’s ManualRTL8187 Wireless LAN User’s ManualRTL8187 Wireless LAN User’s ManualRTL8187 Wireless LAN User’s ManualRTL8187 Wireless LAN User’s ManualAllows you to open the Realtek® RTL8187 Wireless LAN user’s manual.

5 - 85 - 85 - 85 - 85 - 8 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.2.75.2.75.2.75.2.75.2.7 Other informationOther informationOther informationOther informationOther informationThe icons on the top right corner of the screen give additional informationon the motherboard and the contents of the support CD. Click an icon todisplay the specified information.

Motherboard InfoMotherboard InfoMotherboard InfoMotherboard InfoMotherboard InfoDisplays the general specifications of the motherboard.

5.2.65.2.65.2.65.2.65.2.6 ASUS Contact informationASUS Contact informationASUS Contact informationASUS Contact informationASUS Contact informationClick the Contact Contact Contact Contact Contact tab to display the ASUS contact information. You canalso find this information on the inside front cover of this user guide.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 - 95 - 95 - 95 - 95 - 9

Technical support FormTechnical support FormTechnical support FormTechnical support FormTechnical support FormDisplays the ASUS Technical Support Request Form that you have to fill outwhen requesting technical support.

Fi le l istFi lel istFi lel istFi lel istFi lel istDisplays the contents of the support CD and a brief description of each intext format.

Browse this CDBrowse this CDBrowse this CDBrowse this CDBrowse this CDDisplays the support CD contents in graphical format.

5 -105 -105 -105 -105 -10 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.3 Software informationMost of the applications in the support CD have wizards that willconveniently guide you through the installation. View the online help orreadme file that came with the software application for more information.

5.3.15.3.15.3.15.3.15.3.1 ASUS MyLogo2™ASUS MyLogo2™ASUS MyLogo2™ASUS MyLogo2™ASUS MyLogo2™The ASUS MyLogo2™ utility lets you customize the boot logo. The bootlogo is the image that appears on screen during the Power-On-Self-Tests(POST). The ASUS MyLogo™ is automatically installed when you install theASUS Update ASUS Update ASUS Update ASUS Update ASUS Update utility from the support CD. See section “5.2.3 Utilitiesmenu” for details.

To launch the ASUS MyLogo2™:

1. Launch the ASUS Update utility. Refer to section “4.1.1 ASUS Updateutility” for details.

2. Select Opt ions Opt ions Opt ions Opt ions Opt ions from the drop down menu, then click NextNextNextNextNext.3. Check the option Launch MyLogo to replace system bootLaunch MyLogo to replace system bootLaunch MyLogo to replace system bootLaunch MyLogo to replace system bootLaunch MyLogo to replace system boot

logo before f lash ing BIOSlogo before f lash ing BIOSlogo before f lash ing BIOSlogo before f lash ing BIOSlogo before f lash ing BIOS, then click NextNextNextNextNext.4. Select Update BIOS from a f i leUpdate BIOS from a f i leUpdate BIOS from a f i leUpdate BIOS from a f i leUpdate BIOS from a f i le from the drop down menu, then

click NextNextNextNextNext.5. When prompted, locate the

new BIOS file, then click NextNextNextNextNext.The ASUS MyLogo windowappears.

6. From the left window pane,select the folder that containsthe image you intend to use asyour boot logo.

• Before using the ASUS MyLogo2™, use the AFUDOS utility to make acopy of your original BIOS file, or obtain the latest BIOS version fromthe ASUS website. See section “4.1.4 AFUDOS Utility.”

• Make sure that the BIOS item Fu l l Screen Logo Fu l l Screen Logo Fu l l Screen Logo Fu l l Screen Logo Fu l l Screen Logo is set to[Enabled] if you wish to use ASUS MyLogo. See section “4.6.2 BootSettings Configuration.”

• You can create your own boot logo image in GIF, JPG, or BMP fileformats.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -115 -115 -115 -115 -11

9. When the screen returns to the ASUS Update utility, flash the originalBIOS to load the new boot logo.

10. After flashing the BIOS, restart the computer to display the new bootlogo during POST.

8. Adjust the boot image to yourdesired size by selecting avalue on the Rat io Rat io Rat io Rat io Rat io box.

7. When the logo images appearon the right window pane,select an image to enlarge byclicking on it.

5 -125 -125 -125 -125 -12 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

3. Click the R unRunRunRunRun button to perform a cable test.

5.3.25.3.25.3.25.3.25.3.2 AI Net 2AI Net 2AI Net 2AI Net 2AI Net 2The Marvell® Virtual Cable Tester™ (VCT) is a cable diagnostic utility thatreports LAN cable faults and shorts using the Time Domain Reflectometry(TDR) technology. The VCT detects and reports open and shorted cables,impedance mismatches, pair swaps, pair polarity problems, and pair skewproblems of up to 64 ns at one meter accuracy.

The VCT feature reduces networking and support costs through a highlymanageable and controlled network system. This utility can be incorporatedin the network systems software for ideal field support as well asdevelopment diagnostics.

Using the Virtual Cable Tester™Using the Virtual Cable Tester™Using the Virtual Cable Tester™Using the Virtual Cable Tester™Using the Virtual Cable Tester™To use the the Marvell® Virtual Cable Tester™ utility:

1. Launch the VCT utility from the Windows® desktop by clickingStart > Al l Programs > Marvel l > Virtua l Cable TesterStart > Al l Programs > Marvel l > Virtua l Cable TesterStart > Al l Programs > Marvel l > Virtua l Cable TesterStart > Al l Programs > Marvel l > Virtua l Cable TesterStart > Al l Programs > Marvel l > Virtua l Cable Tester.

2. Click Virtua l Cable Tester Virtua l Cable Tester Virtua l Cable Tester Virtua l Cable Tester Virtua l Cable Tester from the menu to display the screenbelow.

• The VCT only runs on systems with Windows® XP or Windows® 2000operating systems.

• The VCT utility only tests Ethernet cables connected to Gigabit LANport(s).

• The R u nR u nR u nR u nR u n button on the Virtual Cable Tester™ main window isdisabled if no problem is detected on the LAN cable(s) connected tothe LAN port(s).

• If you want the system to check the LAN cable before entering theOS, enable the POST Check LAN cab lePOST Check LAN cab lePOST Check LAN cab lePOST Check LAN cab lePOST Check LAN cab le item in the BIOS.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -135 -135 -135 -135 -13

5.3.35.3.35.3.35.3.35.3.3 ASUS PC Probe IIASUS PC Probe IIASUS PC Probe IIASUS PC Probe IIASUS PC Probe IIPC Probe II is a utility that monitors the computer’s vital components, anddetects and alerts you of any problem with these components. PC Probe IIsenses fan rotations, CPU temperature, and system voltages, amongothers. Because PC Probe II is software-based, you can start monitoringyour computer the moment you turn it on. With this utility, you are assuredthat your computer is always at a healthy operating condition.

Install ing PC Probe I IInstall ing PC Probe I IInstall ing PC Probe I IInstall ing PC Probe I IInstall ing PC Probe I ITo install PC Probe II on your computer:

1. Place the support CD to the optical drive. The Dr ivers Dr ivers Dr ivers Dr ivers Dr ivers installation tabappears if your computer has an enabled Autorun feature.

If Autorun is not enabled in your computer, browse the contents of thesupport CD to locate the setup.exe file from the ASUS PC Probe II folder.Double-click the setup.exe file to start installation.

2. Click the Ut i l i t ies Ut i l i t ies Ut i l i t ies Ut i l i t ies Ut i l i t ies tab, then click ASUS PC Probe I IASUS PC Probe I IASUS PC Probe I IASUS PC Probe I IASUS PC Probe I I.3. Follow the screen instructions to complete installation.

Launching PC Probe I ILaunching PC Probe I ILaunching PC Probe I ILaunching PC Probe I ILaunching PC Probe I IYou can launch the PC Probe II right after installation or anytime from theWindows® desktop.

To launch the PC Probe II from the Windows® desktop, click Start Start Start Start Start > A l lA l lA l lA l lA l lPrograms > ASUS Programs > ASUS Programs > ASUS Programs > ASUS Programs > ASUS > PC Probe I I > PC Probe I I v1.00.43PC Probe I I > PC Probe I I v1.00.43PC Probe I I > PC Probe I I v1.00.43PC Probe I I > PC Probe I I v1.00.43PC Probe I I > PC Probe I I v1.00.43. The PCProbe II main window appears.

After launching the application, the PC Probe II icon appears in theWindows® taskbar. Click this icon to close or restore the application.

Using PC Probe I IUsing PC Probe I IUsing PC Probe I IUsing PC Probe I IUsing PC Probe I IMain window

The PC Probe II main window allowsyou to view the current status ofyour system and change the utilityconfiguration. By default, the mainwindow displays the PreferencePreferencePreferencePreferencePreferencesection. You can close or restore thePreference Preference Preference Preference Preference section by clicking on the triangle on the main window righthandle.

C l i c k to c l o se theC l i c k to c l o se theC l i c k to c l o se theC l i c k to c l o se theC l i c k to c l o se theP re fe rence pane lP r e fe rence pane lP r e fe rence pane lP r e fe rence pane lP r e fe rence pane l

5 -145 -145 -145 -145 -14 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

B u t t o nB u t t o nB u t t o nB u t t o nB u t t o n Func t i o nFunc t i o nFunc t i o nFunc t i o nFunc t i o n

Opens the Conf igurat ion Conf igurat ion Conf igurat ion Conf igurat ion Conf igurat ion windowOpens the Repor t Repor t Repor t Repor t Repor t windowOpens the Desktop Management Inter face Desktop Management Inter face Desktop Management Inter face Desktop Management Inter face Desktop Management Inter face windowOpens the Per iphera l Component Interconnect Per iphera l Component Interconnect Per iphera l Component Interconnect Per iphera l Component Interconnect Per iphera l Component Interconnect windowOpens the Windows Management Inst rumentat ion Windows Management Inst rumentat ion Windows Management Inst rumentat ion Windows Management Inst rumentat ion Windows Management Inst rumentat ion windowOpens the hard disk drive, memory, CPU usage windowShows/Hides the P re fe rence P re fe rence P re fe rence P re fe rence P re fe rence sectionMinimizes the applicationCloses the application

Sensor alert

When a system sensor detects a problem, the main window right handleturns red, as the illustrations below show.

When displayed, the monitor panel for that sensor also turns red. Refer tothe Monitor panels Monitor panels Monitor panels Monitor panels Monitor panels section for details.

PreferencesPreferencesPreferencesPreferencesPreferencesYou can customize the application using thePreference section in the main window. Clickthe box before each preference to activate ordeactivate.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -155 -155 -155 -155 -15

Hardware monitor panelsHardware monitor panelsHardware monitor panelsHardware monitor panelsHardware monitor panelsThe hardware monitor panels display the current value of a system sensorsuch as fan rotation, CPU temperature, and voltages.

The hardware monitor panels come in two display modes: hexagonal (large)and rectangular (small). When you check the Enable Monitor ing PanelEnable Monitor ing PanelEnable Monitor ing PanelEnable Monitor ing PanelEnable Monitor ing Paneloption from the PreferencePreferencePreferencePreferencePreference section, the monitor panels appear on yourcomputer’s desktop.

Changing the monitor panels position

To change the position of the monitor panels in the desktop,click the arrow down button of the Scheme Scheme Scheme Scheme Scheme options, thenselect another position from the list box. Click OK OK OK OK OK whenfinished.

Moving the monitor panels

All monitor panels move together using amagnetic effect. If you want to detach amonitor panel from the group, click thehorseshoe magnet icon. You can now moveor reposition the panel independently.

Adjusting the sensor threshold value

You can adjust the sensor thresholdvalue in the monitor panel by clickingthe or buttons. You can also adjustthe threshold values using theConf ig Conf ig Conf ig Conf ig Conf ig window.

You cannot adjust the sensor thresholdvalues in a small monitoring panel.

La rge d i sp l ayLa rge d i sp l ayLa rge d i sp l ayLa rge d i sp l ayLa rge d i sp l ay

Sma l l d i s p l aySma l l d i s p l aySma l l d i s p l aySma l l d i s p l aySma l l d i s p l ay

C l i c k t oC l i c k t oC l i c k t oC l i c k t oC l i c k t oi n c r e a sei n c r e a sei n c r e a sei n c r e a sei n c r e a se

v a l u ev a l u ev a l u ev a l u ev a l u e

C l i c k t oC l i c k t oC l i c k t oC l i c k t oC l i c k t odec r e a sedec r e a sedec r e a sedec r e a sedec r e a se

v a l u ev a l u ev a l u ev a l u ev a l u e

5 -165 -165 -165 -165 -16 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Monitoring sensor alert

The monitor panel turns red when a component value exceeds or is lowerthan the threshold value. Refer to the illustrations below.

La rge d i sp l ayLa rge d i sp l ayLa rge d i sp l ayLa rge d i sp l ayLa rge d i sp l ay

Sma l l d i s p l aySma l l d i s p l aySma l l d i s p l aySma l l d i s p l aySma l l d i s p l ay

WMI browserWMI browserWMI browserWMI browserWMI browserClick to display the WMI(Windows ManagementInstrumentation) browser. Thisbrowser displays various Windows®

management information. Click anitem from the left panel to displayon the right panel. Click the plussign (+) before WMI Informat ionWMI Informat ionWMI Informat ionWMI Informat ionWMI Informat ionto display the available information.

You can enlarge or reduce the browser size by dragging the bottom rightcorner of the browser.

DMI browserDMI browserDMI browserDMI browserDMI browserClick to display the DMI(Desktop Management Interface)browser. This browser displaysvarious desktop and systeminformation. Click the plus sign (+)before DMI Informat ion DMI Informat ion DMI Informat ion DMI Informat ion DMI Informat ion todisplay the available information.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -175 -175 -175 -175 -17

PCI browserPCI browserPCI browserPCI browserPCI browserClick to display the PCI(Peripheral ComponentInterconnect) browser. This browserprovides information on the PCIdevices installed on your system.Click the plus sign (+) before thePCI Informat ion PCI Informat ion PCI Informat ion PCI Informat ion PCI Informat ion item to displayavailable information.

UsageUsageUsageUsageUsageThe Usage Usage Usage Usage Usage browser displays real-time information on the CPU, hard diskdrive space, and memory usage. Click to display the Usage browser.

CPU usage

The CPUCPUCPUCPUCPU tab displays real-time CPUusage in line graph representation.If the CPU has an enabledHyper-Threading, two separate linegraphs display the operation of thetwo logical processors.

Hard disk drive space usage

The Hard D isk Hard D isk Hard D isk Hard D isk Hard D isk tab displays theused and available hard disk drivespace. The left panel of the tablists all logical drives. Click a harddisk drive to display the informationon the right panel. The pie chart atthe bottom of the windowrepresents the used (blue) and theavailable HDD space.

5 -185 -185 -185 -185 -18 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Memory usage

The Memory tab shows both usedand available physical memory. Thepie chart at the bottom of thewindow represents the used (blue)and the available physical memory.

Configuring PC Probe I IConfiguring PC Probe I IConfiguring PC Probe I IConfiguring PC Probe I IConfiguring PC Probe I IClick to view and adjust the sensor threshold values.

The Conf ig Conf ig Conf ig Conf ig Conf ig window has two tabs: Sensor/Threshold Sensor/Threshold Sensor/Threshold Sensor/Threshold Sensor/Threshold and PreferencePreferencePreferencePreferencePreference.The Sensor/Threshold Sensor/Threshold Sensor/Threshold Sensor/Threshold Sensor/Threshold tab enables you to activate the sensors or toadjust the sensor threshold values. The Preference Preference Preference Preference Preference tab allows you tocustomize sensor alerts, or change the temperature scale.

Loads the de fau l tLoads the de fau l tLoads the de fau l tLoads the de fau l tLoads the de fau l tt h resho l d va l uesth resho l d va l uesth resho l d va l uesth resho l d va l uesth resho l d va l uesfo r each senso rfo r each senso rfo r each senso rfo r each senso rfo r each senso r

App l i e s you rApp l i e s you rApp l i e s you rApp l i e s you rApp l i e s you rc h a n g e sc h a n g e sc h a n g e sc h a n g e sc h a n g e s

Cance l s o rCance l s o rCance l s o rCance l s o rCance l s o ri gno re s you ri gno re s you ri gno re s you ri gno re s you ri gno re s you r

c h a n g e sc h a n g e sc h a n g e sc h a n g e sc h a n g e s

Loads your savedLoads your savedLoads your savedLoads your savedLoads your savedconf igurat ionconf igurat ionconf igurat ionconf igurat ionconf igurat ionSaves you rSaves you rSaves you rSaves you rSaves you rcon f i gu r a t i oncon f i gu r a t i oncon f i gu r a t i oncon f i gu r a t i oncon f i gu r a t i on

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -195 -195 -195 -195 -19

5.3.45.3.45.3.45.3.45.3.4 Cool ‘n’ Quiet™ TechnologyCool ‘n’ Quiet™ TechnologyCool ‘n’ Quiet™ TechnologyCool ‘n’ Quiet™ TechnologyCool ‘n’ Quiet™ TechnologyThe motherboard supports the AMD Cool ‘n’ Quiet™ Technology thatdynamically and automatically change the CPU speed, voltage, and amountof power depending on the task the CPU performs.

Enabling Cool ‘n’ Quiet™ TechnologyEnabling Cool ‘n’ Quiet™ TechnologyEnabling Cool ‘n’ Quiet™ TechnologyEnabling Cool ‘n’ Quiet™ TechnologyEnabling Cool ‘n’ Quiet™ TechnologyTo enable Cool ‘n’ Quiet™ Technology:

1. Turn on the system and enter BIOS by pressing the <Del> key duringthe Power On Self-Tests (POST).

2. Go to the Advanced Menu -> CPU Conf igurat ionAdvanced Menu -> CPU Conf igurat ionAdvanced Menu -> CPU Conf igurat ionAdvanced Menu -> CPU Conf igurat ionAdvanced Menu -> CPU Conf igurat ion, select theitem Cool ‘n ’QuietCool ‘n ’QuietCool ‘n ’QuietCool ‘n ’QuietCool ‘n ’Quiet and set it to Enab ledEnab ledEnab ledEnab ledEnab led. See section “4.4.2 CPUConfiguration.”

3. In the Power Power Power Power Power menu, select the item ACPI 2.0 SupportACPI 2.0 SupportACPI 2.0 SupportACPI 2.0 SupportACPI 2.0 Support and set itto Y e sY e sY e sY e sY e s. See section “4.5 Power Menu.”

4. Save your changes and exit BIOS Setup.5. Reboot your computer and set your Power Options Properties

depending on your operating system.

The Cool ‘n’ Quiet™ Technology item is set to [Disabled] by default inthe BIOS.

WindowsWindowsWindowsWindowsWindows®®®®® 2000/XP 2000/XP 2000/XP 2000/XP 2000/XP1. From the Windows® 2000/XP operating system, click the Sta r tSta r tSta r tSta r tSta r t

button. Select Sett ingsSett ingsSett ingsSett ingsSett ings, thenContro l Pane lContro l Pane lContro l Pane lContro l Pane lContro l Pane l.

2. Make sure the Control Panel isset to Classic View.

3. Double-click the D isp lay D isp lay D isp lay D isp lay D isp lay icon inthe Control Panel then select theScreen SaverScreen SaverScreen SaverScreen SaverScreen Saver tab.

4. Click the Power . . .Power . . .Power . . .Power . . .Power . . . button. Thefollowing dialog box appears.

5. From the Power schemesPower schemesPower schemesPower schemesPower schemescombo list box, select M in ima lM in ima lM in ima lM in ima lM in ima lPower ManagementPower ManagementPower ManagementPower ManagementPower Management.

6. Click OK OK OK OK OK to effect settings.

Make sure to install the Cool‘n’ Quiet™ driver andapplication before using this feature.

5 -205 -205 -205 -205 -20 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Launching the Cool ‘n’ Quiet™ softwareLaunching the Cool ‘n’ Quiet™ softwareLaunching the Cool ‘n’ Quiet™ softwareLaunching the Cool ‘n’ Quiet™ softwareLaunching the Cool ‘n’ Quiet™ softwareThe motherboard support CD includes the Cool ‘n’ Quie!™ software thatenables you to view your system’s real-time CPU Frequency and voltage.

To launch the Cool ‘n’ Quiet™ program:

1. If you are using Windows® 2000, click the Sta r tSta r tSta r tSta r tSta r t button. SelectPrograms-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.

2. If you are using Windows® XP, click the Sta r tSta r tSta r tSta r tSta r t button. Select A l lA l lA l lA l lA l lPrograms-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.

3. The Cool ‘n’ Quiet!™ technology screen appears and displays thecurrent CPU Frequency and CPU Voltage.

Make sure to install the Cool ‘n’ Quiet™ software from the motherboardsupport CD. Refer to section “5.2.3 Utilities menu” for details.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -215 -215 -215 -215 -21

5.3.55.3.55.3.55.3.55.3.5 Audio configurationsAudio configurationsAudio configurationsAudio configurationsAudio configurationsThe Realtek® ALC882 audio CODEC provides 8-channel audio capability todeliver the ultimate audio experience on your computer. The softwareprovides Jack-Sensing function, S/PDIF Out support, and interruptcapability. The ALC882 also includes the Realtek® proprietary UAJ®

(Universal Audio Jack) technology for all audio ports, eliminating cableconnection errors and giving users plug and play convenience.

Follow the installation wizard to install the Rea l tekRea l tekRea l tekRea l tekRea l tek®®®®® Audio Dr iver Audio Dr iver Audio Dr iver Audio Dr iver Audio Dr iver fromthe support CD that came with the motherboard package.

If the Realtek audio software is correctly installed, you will find the RealtekHD Audio Manager icon on the taskbar.

From the taskbar, double-click on the SoundEffect SoundEffect SoundEffect SoundEffect SoundEffect icon to display theRealtek HD Audio ManagerRealtek HD Audio ManagerRealtek HD Audio ManagerRealtek HD Audio ManagerRealtek HD Audio Manager.

Rea l tek HD Aud io Manage rRea l tek HD Aud io Manage rRea l tek HD Aud io Manage rRea l tek HD Aud io Manage rRea l tek HD Aud io Manage r

Con t r o lCon t r o lCon t r o lCon t r o lCon t r o ls e t t i n g ss e t t i n g ss e t t i n g ss e t t i n g ss e t t i n g sw i n d o ww i n d o ww i n d o ww i n d o ww i n d o w

ConfigurationConfigurationConfigurationConfigurationConfigurationo p t i o n so p t i o n so p t i o n so p t i o n so p t i o n s

I n f o rmat i onI n fo rmat i onI n fo rmat i onI n fo rmat i onI n fo rmat i onb u t t o nb u t t o nb u t t o nb u t t o nb u t t o n

Realtek HD Audio ManagerRealtek HD Audio ManagerRealtek HD Audio ManagerRealtek HD Audio ManagerRealtek HD Audio Manager

Too l bu t tonToo l bu t tonToo l bu t tonToo l bu t tonToo l bu t ton

E x i tE x i tE x i tE x i tE x i tb u t t o nb u t t o nb u t t o nb u t t o nb u t t o n

M i n im i z eM i n im i z eM i n im i z eM i n im i z eM i n im i z eb u t t o nb u t t o nb u t t o nb u t t o nb u t t o n

5 -225 -225 -225 -225 -22 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

InformationInformationInformationInformationInformationClick the information button( ) to display informationabout the audio driver version,DirectX version, audio controller,audio codec, and language setting.

MinimizeMinimizeMinimizeMinimizeMinimizeClick the minimize button ( ) to minimize the window.

Ex itEx itEx itEx itEx it

Click the exit button ( ) to exit the Realtek HD Audio Manager.

Configuration optionsConfiguration optionsConfiguration optionsConfiguration optionsConfiguration optionsClick any of the tabs in this area to configure your audio settings. Click thearrow button ( ) to display more options.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -235 -235 -235 -235 -23

Sound Effect

The Realtek® ALC882 Audio CODECallows you to set your listeningenvironment, adjust the equalizer,set the karaoke, or selectpre-programmed equalizer settingsfor your listening pleasure.

To set the sound effect options:1. From the Realtek HD Audio

Manager, click the SoundSoundSoundSoundSoundEffect Ef fect Ef fect Ef fect Ef fect tab.

2. Click the shortcut buttons or the drop-down menus for options onchanging the acoustic environment, adjust the equalizer, or set thekaraoke to your desired settings.

3. Click to effect the Sound Effect settings and exit.

Mixer

The Mixer option allows you toconfigure audio output (playback)volume and audio input (record)volume.

To set the mixer options:1. From the Realtek HD Audio

Manager, click the M ixer M ixer M ixer M ixer M ixer tab.2. Turn the volume buttons to

adjust the Playback and/orRecord volume.

The Mixer option activates voice input from all channels by default. Makesure to set all channels to mute ( ) if you do not want voice input.

3. Make adjustments to Wave, SW Synth, Front, Rear, Subwoofer, CDvolume, Mic volume, Line Volume, and Stereo mix by clicking thecontrol tabs and dragging them up and down until you get the desiredlevels.

4. Click to effect the Mixer settings and exit.

5 -245 -245 -245 -245 -24 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Audio I/O

The Audio I/O option allows youconfigure your input/outputsettings.

To set the Audio I/O options:

1. From the Realtek HD AudioManager, click the Aud io I/OAudio I/OAudio I/OAudio I/OAudio I/Otab.

2. Click the drop-down menu toselect the channelconfiguration.

3. The control settings window displays the status of connected devices.Click for analog and digital options.

4. Click <OK> to effect the Audio I/O settings and exit

Microphone

The Microphone option allows youconfigure your input/output settingsand to check if your audio devicesare connected properly.

To set the Microphone options:

1. From the Realtek HD AudioManager, click theMicrophone Microphone Microphone Microphone Microphone tab.

2. Click the Noise Suppress ionNoise Suppress ionNoise Suppress ionNoise Suppress ionNoise Suppress ionoption button to reduce the static background noise when recording.

3. Click the Acoust ic Echo Cancel lat ion Acoust ic Echo Cancel lat ion Acoust ic Echo Cancel lat ion Acoust ic Echo Cancel lat ion Acoust ic Echo Cancel lat ion option button to reducethe echo from the front speakers when recording.

4. Click to effect the Microphone settings and exit.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -255 -255 -255 -255 -25

3D Audio Demo

The 3D Audio Demo option givesyou a demonstration of the 3Daudio feature.

To start the 3D Audio Demo:

1. From the Realtek HD AudioManager, click the 3D Aud io3D Aud io3D Aud io3D Aud io3D Aud ioDemo Demo Demo Demo Demo tab.

2. Click the option buttons tochange the sound, movingpath, or environment settings.

3. Click to test your settings.4. Click to effect the 3D Audio Demo settings and exit.

5 -265 -265 -265 -265 -26 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.4 RAID configurationsThe motherboard comes with a RAID controller integrated in the ULI M1575Southbridge that allows you to configure Serial ATA hard disk drives asRAID sets. The motherboard supports the following RAID configurations.

RA ID 0RAID 0RAID 0RAID 0RAID 0 (Data striping) optimizes two identical hard disk drives to read andwrite data in parallel, interleaved stacks. Two hard disks perform the samework as a single drive but at a sustained data transfer rate, double that ofa single disk alone, thus improving data access and storage. Use of twonew identical hard disk drives is required for this setup.

RA ID 1RAID 1RAID 1RAID 1RAID 1 (Data mirroring) copies and maintains an identical image of datafrom one drive to a second drive. If one drive fails, the disk arraymanagement software directs all applications to the surviving drive as itcontains a complete copy of the data in the other drive. This RAIDconfiguration provides data protection and increases fault tolerance to theentire system. Use two new drives or use an existing drive and a new drivefor this setup. The new drive must be of the same size or larger than theexisting drive.

RAID 0+1RAID 0+1RAID 0+1RAID 0+1RAID 0+1 is data striping and data mirroring combined without parity(redundancy data) having to be calculated and written. With the RAID 0+1configuration you get all the benefits of both RAID 0 and RAID 1configurations. Use four new hard disk drives or use an existing drive andthree new drives for this setup.

RA ID 5RAID 5RAID 5RAID 5RAID 5 stripes both data and parity information across three or more harddisk drives. Among the advantages of RAID 5 configuration include betterHDD performance, fault tolerance, and higher storage capacity. The RAID 5configuration is best suited for transaction processing, relational databaseapplications, enterprise resource planning, and other business systems.Use a minimum of three identical hard disk drives for this setup.

JBODJBODJBODJBODJBOD (Spanning) stands for Just a Bunch of DisksJust a Bunch of DisksJust a Bunch of DisksJust a Bunch of DisksJust a Bunch of Disks and refers to harddisk drives that are not yet configured as a RAID set. This configurationstores the same data redundantly on multiple disks that appear as a singledisk on the operating system. Spanning does not deliver any advantageover using separate disks independently and does not provide faulttolerance or other RAID performance benefits.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -275 -275 -275 -275 -27

5.4.15.4.15.4.15.4.15.4.1 Installing hard disksInstalling hard disksInstalling hard disksInstalling hard disksInstalling hard disksThe motherboard supports Ultra DMA 133/100/66 and Serial ATA harddisk drives. For optimal performance, install identical drives of the samemodel and capacity when creating a disk array.

Install ing Serial ATA (SATA) hard disksInstall ing Serial ATA (SATA) hard disksInstall ing Serial ATA (SATA) hard disksInstall ing Serial ATA (SATA) hard disksInstall ing Serial ATA (SATA) hard disksTo install the SATA hard disks for a RAID configuration:

1. Install the SATA hard disks into the drive bays.2. Connect the SATA signal cables.3. Connect a SATA power cable to the power connector on each drive.

5.4.25.4.25.4.25.4.25.4.2 ULIULIULIULIULI®®®®® RAID configurations RAID configurations RAID configurations RAID configurations RAID configurationsThe ULI® RAID controller supports RAID 0, RAID 1, RAID 0+1, RAID 5, andJBOD configurations. Use the ULI® RAID BIOS Setup utility to configure adisk array.

Entering the ULIEntering the ULIEntering the ULIEntering the ULIEntering the ULI®®®®® RAID BIOS Setup Util ity RAID BIOS Setup Util ity RAID BIOS Setup Util ity RAID BIOS Setup Util ity RAID BIOS Setup Util ityTo enter the ULI® RAID BIOS setup utility:1. Boot up your computer, and press <Del> during POST to enter the

BIOS setup.2. In the Ma in MenuMain MenuMain MenuMain MenuMain Menu, go to Storage Conf igurat ionStorage Conf igurat ionStorage Conf igurat ionStorage Conf igurat ionStorage Conf igurat ion, and set the

Onboard SATA Boot ROM Onboard SATA Boot ROM Onboard SATA Boot ROM Onboard SATA Boot ROM Onboard SATA Boot ROM item to [Enabled].3. Press <F10> to save the changes and exit.4. During POST, press <Ctrl+A>.

The RAID BIOS setup screens shown in this section are for referenceonly, and may not exactly match the items on your screen.

You may also set the RAID configurations in Windows® OS after youhave installed the Serial ATA RAID driver. See section “5.2.4 MakeDisk menu” for details.

5 -285 -285 -285 -285 -28 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

The Main Menu on the upper left side allows you to select an operation toperform. The Main Menu options include:Create RAID 0 Str ip ing x2 for Performance Create RAID 0 Str ip ing x2 for Performance Create RAID 0 Str ip ing x2 for Performance Create RAID 0 Str ip ing x2 for Performance Create RAID 0 Str ip ing x2 for Performance - creates a new legacy

RAID set or allocates spare drives.Create RAID 0+1 for Str ip ing, Mirror ing Create RAID 0+1 for Str ip ing, Mirror ing Create RAID 0+1 for Str ip ing, Mirror ing Create RAID 0+1 for Str ip ing, Mirror ing Create RAID 0+1 for Str ip ing, Mirror ing - creates a RAID setup with

all the benefits of both RAID 0 and RAID 1 configuration.C reatCreatCreatCreatCreate JBOD for integrated capacity e JBOD for integrated capacity e JBOD for integrated capacity e JBOD for integrated capacity e JBOD for integrated capacity - creates a JBOD configuration.Str ipe S ize Str ipe S ize Str ipe S ize Str ipe S ize Str ipe S ize - sets the stripe size.Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion - deletes a selected RAID set and

partition.Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion - deletes all current RAID

set(s) and partition(s).Rebui ld RAID array Rebui ld RAID array Rebui ld RAID array Rebui ld RAID array Rebui ld RAID array - rebuilds mirror drive(s).Create RAID 5 for Rel iab i l i tyCreate RAID 5 for Rel iab i l i tyCreate RAID 5 for Rel iab i l i tyCreate RAID 5 for Rel iab i l i tyCreate RAID 5 for Rel iab i l i ty - creates a RAID 5 configuration

On the upper right side of the screen is the legend box. The keys on thelegend box allow you to navigate through the setup menu options. Thefollowing lists the keys in the legend box and their corresponding functions.

SPACESPACESPACESPACESPACE : Select an item↑↑↑↑↑, , , , , ↓↓↓↓↓ : Move cursor to the next itemEnterEnte rEnte rEnte rEnte r : Confirms a selected itemE S CE S CE S CE S CE S C : Exit

Create RAID 0 Striping x2 for PerformanceCreate RAID 1 Mirroring for Reliability

Create RAID 0+1 Striping, MirroringCreate JBOD for integrated Capacity SPACE: SelectStripe Size 16K ↑↑↑↑↑ ↓ ↓ ↓ ↓ ↓ : Moving CursorDelete RAID Settings & Partition 16K Enter: Select & FinishDelete All RAID Settings & Partition ESC: ExitRebuild RAID ArrayCreate RAID 5 for Reliability

Drive Model Mode Capacity RAID Array/TypeChannel 0 Master: XXXXXXXXXXX SATA 2 XXXXX MBChannel 1 Master: XXXXXXXXXXX SATA 2 XXXXX MBChannel 2 Master: XXXXXXXXXXX SATA 2 XXXXX MBChannel 3 Master: XXXXXXXXXXX SATA 2 XXXXX MB

Capacity RAID Type Stripe Size RAID NameRAID Array A :RAID Array B :RAID Array C :

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -295 -295 -295 -295 -29

Creating a RAID 0 configurationCreating a RAID 0 configurationCreating a RAID 0 configurationCreating a RAID 0 configurationCreating a RAID 0 configurationTo create a RAID 0 set:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Create RAID 0 Str ip ing for PerformanceCreate RAID 0 Str ip ing for PerformanceCreate RAID 0 Str ip ing for PerformanceCreate RAID 0 Str ip ing for PerformanceCreate RAID 0 Str ip ing for Performance then press <Enter>.2. Use the up or down arrow keys to select a drive then press <Space>

or <Enter>. The striped mark “S” appears before a selected drive.3. Repeat step 2 to select the second drive.4. The utility prompts the following warning message:

Data on RAID drives will be deleted (Y/N)?

Press <Y> to continue or press <N> to return to the menu.5. Key in a RAID name with a maximum of eight (8) alphanumeric

characters then press <Enter>. Do not use special characters orsymbols.

6. The utility displays the RAID Array settings at the bottom of thescreen.

Drive Model Mode Capacity RAID Array/TypeChannel 0 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/0x2Channel 1 Master: XXXXXXXXXXX SATA 2 XXXXX MBChannel 2 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/0x2Channel 3 Master: XXXXXXXXXXX SATA 2 XXXXX MB

Capacity RAID Type Stripe Size RAID NameRAID Array A : XXXXX GB 0X2 16K RAID0RAID Array B :RAID Array C :

5 -305 -305 -305 -305 -30 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Creating a RAID 1 configurationCreating a RAID 1 configurationCreating a RAID 1 configurationCreating a RAID 1 configurationCreating a RAID 1 configurationTo create a RAID 1 set:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Create RAID 1 Mirror ing for Rel iab i l i ty Create RAID 1 Mirror ing for Rel iab i l i ty Create RAID 1 Mirror ing for Rel iab i l i ty Create RAID 1 Mirror ing for Rel iab i l i ty Create RAID 1 Mirror ing for Rel iab i l i ty then press <Enter>.2. Use the up or down arrow keys to select a drive then press <Space>

or <Enter>. The striped mark “M” appears before a selected drive.3. Repeat step 2 to select the second drive.4. The utility prompts the following warning message:

Create RAID 1 (Y/N)?

Press <Y> to continue or press <N> to return to the menu.5. Key in a RAID name with a maximum of eight (8) alphanumeric

characters then press <Enter>. Do not use special characters orsymbols.

6. The utility prompts the following confirmation message:

Duplicate Data from M to m (Y/N)?

Press <Y> to duplicate data from the source disk “M” to the targetdisk “m” or press <N> to create a RAID 1 set without duplicating thedata.

7. If you selected <Y>, the utility will duplicate your data. The followingprogress bar appears.

8. The utility displays the RAID Array settings at the bottom of thescreen.

12345678901234567890123456789012123456789012345671234567890123456789012345678901212345678901234567123456789012345678901234567890121234567890123456712345678901234567890123456789012123456789012345671234567890123456789012345678901212345678901234567 50% completed.123456789012345678123456789012345678123456789012345678123456789012345678

Drive Model Mode Capacity RAID Array/TypeChannel 0 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/1Channel 1 Master: XXXXXXXXXXX SATA 2 XXXXX MBChannel 2 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/1Channel 3 Master: XXXXXXXXXXX SATA 2 XXXXX MB

Capacity RAID Type Stripe Size RAID NameRAID Array A : XXXXX MB 1 RAID1RAID Array B :RAID Array C :

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -315 -315 -315 -315 -31

Creating a JBOD configurationCreating a JBOD configurationCreating a JBOD configurationCreating a JBOD configurationCreating a JBOD configurationTo create a JBOD set:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Create JBOD for integrated capacity Create JBOD for integrated capacity Create JBOD for integrated capacity Create JBOD for integrated capacity Create JBOD for integrated capacity then press <Enter>.2. Use the up or down arrow keys to select a drive then press <Space>

or <Enter>. The striped mark “J” appears before a selected drive.3. Repeat step 2 to select the second drive.4. The utility prompts the following warning message:

Data on RAID drives will be deleted (Y/N)?

Press <Y> to continue or press <N> to return to the menu.

Creating a RAID 0+1 configurationCreating a RAID 0+1 configurationCreating a RAID 0+1 configurationCreating a RAID 0+1 configurationCreating a RAID 0+1 configurationTo create a RAID 0+1 set:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Create RAID 0+1 Str ip ing, Mirror ing Create RAID 0+1 Str ip ing, Mirror ing Create RAID 0+1 Str ip ing, Mirror ing Create RAID 0+1 Str ip ing, Mirror ing Create RAID 0+1 Str ip ing, Mirror ing then press <Enter>.2. The utility prompts the following warning message:

Data on first 4 drives will be deleted (Y/N)?

Press <Y> to continue or press <N> to return to the menu.3. Key in a RAID name with a maximum of eight (8) alphanumeric

characters then press <Enter>. Do not use special characters orsymbols.

4. The utility displays the RAID Array settings at the bottom of thescreen.

Drive Model Mode Capacity RAID Array/TypeChannel 0 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/RAID0+1Channel 1 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/RAID0+1Channel 2 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/RAID0+1Channel 3 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/RAID0+1

Capacity RAID Type Stripe Size RAID NameRAID Array A : XXXXX MB 0+1 X4 RAID01RAID Array B :RAID Array C :

5 -325 -325 -325 -325 -32 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Setting the Stripe SizeSetting the Stripe SizeSetting the Stripe SizeSetting the Stripe SizeSetting the Stripe SizeTo set the stripe size:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Str ipe S ize Str ipe S ize Str ipe S ize Str ipe S ize Str ipe S ize then press <Enter>.2. Use the up or down arrow keys to select a stripe size then press

<Enter>.3. The stripe size is displayed beside the Stripe Size menu item.

T I P : T I P : T I P : T I P : T I P : For server systems, we recommend using a lower array blocksize. For multimedia computer systems used mainly for audio andvideo editing, we recommend a higher array block size for optimumperformance.

Drive Model Mode Capacity RAID Array/TypeChannel 0 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/JBODChannel 1 Master: XXXXXXXXXXX XXXXX MBChannel 2 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/JBODChannel 3 Master: XXXXXXXXXXX SATA 2 XXXXX MB

Capacity RAID Type Stripe Size RAID NameRAID Array A : XXXXX MB JBOD RAIDJRAID Array B :RAID Array C :

5. Key in a RAID name with a maximum of eight (8) alphanumericcharacters then press <Enter>. Do not use special characters orsymbols.

6. The utility displays the RAID Array settings at the bottom of thescreen.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -335 -335 -335 -335 -33

Deleting a RAID configurationDeleting a RAID configurationDeleting a RAID configurationDeleting a RAID configurationDeleting a RAID configurationTo delete a RAID set:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion Delete RAID Sett ings & Part it ion then press <Enter>.2. Use the up or down arrow keys to select a RAID set then press

<Space> or <Enter>. The striped mark “E” appears before a selecteddrive.

3. The utility prompts the following warning message:

Data on RAID drives will be deleted (Y/N)?

Press <Y> to continue or press <N> to return to the menu.Pressing <Y> removes the deleted RAID Array item from the list at thebottom of the screen.

Deleting All RAID configurationsDeleting All RAID configurationsDeleting All RAID configurationsDeleting All RAID configurationsDeleting All RAID configurationsTo delete all RAID sets:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion Delete Al l RAID Sett ings & Part it ion then press <Enter>.2. The utility prompts the following warning message:

Data on RAID drives will be deleted (Y/N)?

Press <Y> to continue or press <N> to return to menu.Pressing <Y> removes all the RAID Array items from the list at thebottom of the screen.

5 -345 -345 -345 -345 -34 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Rebuilding a RAID arrayRebuilding a RAID arrayRebuilding a RAID arrayRebuilding a RAID arrayRebuilding a RAID arrayThis option allows you to rebuild an existing RAID array.

To rebuild a RAID array:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Rebui ld RAID Array Rebui ld RAID Array Rebui ld RAID Array Rebui ld RAID Array Rebui ld RAID Array then press <Enter>.2. Use the up or down arrow keys to select the source drive from which

to rebuild then press <Enter>. The striped mark “R” appears before aselected drive.

3. The utility prompts if you want to proceed with rebuilding the array.Press <Y> to continue or press <N> to return to the menu.

Creating a RAID 5 configurationCreating a RAID 5 configurationCreating a RAID 5 configurationCreating a RAID 5 configurationCreating a RAID 5 configurationTo create a RAID 5 set:1. From the ULI RAID BIOS Setup utility menu, move the cursor to

Create RAID 5 for Rel iab i l i ty Create RAID 5 for Rel iab i l i ty Create RAID 5 for Rel iab i l i ty Create RAID 5 for Rel iab i l i ty Create RAID 5 for Rel iab i l i ty then press <Enter>.2. Use the up or down arrow keys to select a drive then press <Space>

or <Enter>. The striped mark “5” appears before a selected drive.3. Repeat step 2 to select the second and third drives.4. The utility prompts the following warning message:

Data on RAID drives will be deleted (Y/N)?

Press <Y> to continue or press <N> to return to the menu.5. Key in a RAID name with a maximum of eight (8) alphanumeric

characters then press <Enter>. Do not use special characters orsymbols.

6. The utility displays the RAID Array settings at the bottom of thescreen.

Drive Model Mode Capacity RAID Array/TypeChannel 0 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/5Channel 1 Master: XXXXXXXXXXX XXXXX MBChannel 2 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/5Channel 3 Master: XXXXXXXXXXX SATA 2 XXXXX MB RAID A/5

Capacity RAID Type Stripe Size RAID NameRAID Array A : 160 GB 5 16K RAID5RAID Array B :RAID Array C :

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -355 -355 -355 -355 -35

5.4.35.4.35.4.35.4.35.4.3 Silicon ImageSilicon ImageSilicon ImageSilicon ImageSilicon Image®®®®® RAID configurations RAID configurations RAID configurations RAID configurations RAID configurationsThe Silicon Image RAID controller supports RAID 0 and RAID 1configurations. Use the Silicon Image RAID utility to configure a disk array.

Setting the BIOS RAID itemsSetting the BIOS RAID itemsSetting the BIOS RAID itemsSetting the BIOS RAID itemsSetting the BIOS RAID itemsAfter installing the hard disk drives, make sure to set the necessary RAIDitems in the BIOS before setting your RAID configuration.

To set the BIOS RAID items:

1. Boot the system and press <Del> during the Power-On Self-Test(POST) to enter the BIOS Setup Utility.

2. From the Advanced > Onboard Devices Conf igurat ion Advanced > Onboard Devices Conf igurat ion Advanced > Onboard Devices Conf igurat ion Advanced > Onboard Devices Conf igurat ion Advanced > Onboard Devices Conf igurat ion menuitem in the BIOS set the S i l icon Image Contro l ler S i l icon Image Contro l ler S i l icon Image Contro l ler S i l icon Image Contro l ler S i l icon Image Contro l ler item to RAIDMode. See section “4.4.4 Onboard Devices Configuration” for details.

3. Save your changes and Exit Setup.

Launching the Sil icon Image Array Management SoftwareLaunching the Sil icon Image Array Management SoftwareLaunching the Sil icon Image Array Management SoftwareLaunching the Sil icon Image Array Management SoftwareLaunching the Sil icon Image Array Management SoftwareLaunch the Silicon Image Array Management software from Windows® XP byclicking the Sta r tSta r tSta r tSta r tSta r t button and selecting Al l Programs > S i l icon ImageAl l Programs > S i l icon ImageAl l Programs > S i l icon ImageAl l Programs > S i l icon ImageAl l Programs > S i l icon Image> Sam> Sam> Sam> Sam> Sam

For details on the Silicon Image SATARaid™ RAID configuration, referto the “Sil3132 SATA RAID User’s Manual” in your motherboardsupport CD.

5 -365 -365 -365 -365 -36 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

Entering the Sil icon Image BIOS RAID Configuration Util ityEntering the Sil icon Image BIOS RAID Configuration Util ityEntering the Sil icon Image BIOS RAID Configuration Util ityEntering the Sil icon Image BIOS RAID Configuration Util ityEntering the Sil icon Image BIOS RAID Configuration Util ityTo enter the Silicon Image BIOS RAID configuration utility:1. Boot up your computer.2. During POST, press <Ctrl+S> or <F4>.

The RAID BIOS setup screens shown in this section are for referenceonly, and may not exactly match the items on your screen.

The Main Menu on the upper left corner allows you to select an operationto be performed. The Main Menu options include the following:Create RAID setCreate RAID setCreate RAID setCreate RAID setCreate RAID set - creates a new legacy RAID set or allocates spare drives.Delete RAID set Delete RAID set Delete RAID set Delete RAID set Delete RAID set - deletes a RAID set or deallocates a spare drive.Rebui ld RAID1 set Rebui ld RAID1 set Rebui ld RAID1 set Rebui ld RAID1 set Rebui ld RAID1 set - rebuilds a RAID 1 set (e.g., swapped drives).Resolve Conf l icts Resolve Conf l icts Resolve Conf l icts Resolve Conf l icts Resolve Conf l icts - automatically restores disrupted drives on a RAID set.Low Level FormatLow Level FormatLow Level FormatLow Level FormatLow Level Format - creates a pattern of reference marks on a drive.

Formatting the disks erases all data previously stored in the drive.Logica l Dr ive InfoLogica l Dr ive InfoLogica l Dr ive InfoLogica l Dr ive InfoLogica l Dr ive Info -shows the current configuration of each RAID set.On the upper right corner of the screen is the Help message box. Themessage describes the function of each menu item. At the bottom of thescreen is the legend box. The keys on the legend box allow you to navigatethrough the setup menu options. The following lists the keys found in thelegend box and their corresponding functions.

↑↑↑↑↑, , , , , ↓↓↓↓↓ : Select/Move to the next itemE S CE S CE S CE S CE S C : Previous MenuEnterEnte rEnte rEnte rEnte r : SelectCt r l -ECt r l -ECt r l -ECt r l -ECt r l -E : Exit

Create RAID setDelete RAID setRebuild Raid1 setResolve ConflictsLow Level FormatLogical Drive Info

↑↓↑↓↑↓↑↓↑↓:Select Menu ESC:Previous Menu Enter:Select Ctrl-E:Exit

MAIN MENU

PHYSICAL DRIVE

0 XXXXXXXXXXX XXXXXXMB1 XXXXXXXXXXX XXXXXXMB2 XXXXXXXXXXX XXXXXXMB3 XXXXXXXXXXX XXXXXXMB

STXXXXXXXXX XXXXXXMBSTXXXXXXXXX XXXXXXMBSTXXXXXXXXX XXXXXXMBSTXXXXXXXXX XXXXXXMB

LOGICAL DRIVE

HELP

Press “Enter” to createRAID set

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -375 -375 -375 -375 -37

Creating a RAID 0 set (Striped)Creating a RAID 0 set (Striped)Creating a RAID 0 set (Striped)Creating a RAID 0 set (Striped)Creating a RAID 0 set (Striped)To create a RAID set:

1. From the SiliconImage configurationutility main menu,select Create RAIDCreate RAIDCreate RAIDCreate RAIDCreate RAIDset se t se t se t se t then press<Enter> to display anoption menu.

2. Select RA ID 0RAID 0RAID 0RAID 0RAID 0 thenpress <Enter> todisplay the following.

By default, Auto configuration sets the stripe size to 64K and setsthe logical drives based on the physical drives installed.

MAIN MENU

Create RAID setDelete RAID setRebuild Raid1 setResolve ConflictsLow Level FormatLogical Drive Info

RAID0RAID1RAID5RAID10

SPARE DRIVECONCATENATION

MAIN MENU

Auto configurationManual configuration

MAIN MENU

Auto configurationManual configuration

chunk size4K8K16K32K64K128K

3. Select your desiredmethod ofconfiguration.

Auto conf igurat ionAuto conf igurat ionAuto conf igurat ionAuto conf igurat ionAuto conf igurat iona. Select Auto Configuration the press <Enter>.b. The utility prompts a message to input the RAID size, use the up

or down arrow keys to set the RAID size then press <Enter>.c. Press <Y> to confirm or <N> to return to the Main Menu.

Manual conf igurat ionManual conf igurat ionManual conf igurat ionManual conf igurat ionManual conf igurat iona. Select Manua lManua lManua lManua lManua l

conf igurat ionconf igurat ionconf igurat ionconf igurat ionconf igurat ionand press<Enter>. Thefollowing pop-upmenu appears.

b. Use the up ordown arrow keysto select a chunksize appropriateto your drive usage }then press <Enter>.

5 -385 -385 -385 -385 -38 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

2. Select RA ID 1RAID 1RAID 1RAID 1RAID 1 thenpress <Enter> todisplay the following.

Creating a RAID 1 set (Mirrored)Creating a RAID 1 set (Mirrored)Creating a RAID 1 set (Mirrored)Creating a RAID 1 set (Mirrored)Creating a RAID 1 set (Mirrored)To create a RAID 1 set:

1. From the SiliconImage configurationutility main menu,select Create RAIDCreate RAIDCreate RAIDCreate RAIDCreate RAIDset se t se t se t se t then press<Enter>. Thefollowing sub-menuappears.

c. The selection bar movesto the Physical Drivemenu. Using the up ordown arrow keys, selecta drive then press<Enter> to set thefirst drive of the RAIDset.

d. Repeat step c to set the second, third, and fourth drive. Thenumber of available drives depend on the installed and enabledphysical drives in the system.

e. The utility prompts a message to input the RAID size, use the upor down arrow keys to set the RAID size then press <Enter>.

f. Press <Y> to confirm or <N> to return to the Main Menu.

PHYSICAL DRIVE

0 XXXXXXXXXXX XXXXXXMB1 XXXXXXXXXXX XXXXXXMB2 XXXXXXXXXXX XXXXXXMB3 XXXXXXXXXXX XXXXXXMB

MAIN MENU

Create RAID setDelete RAID setRebuild Raid1 setResolve ConflictsLow Level FormatLogical Drive Info

RAID0RAID1RAID10

SPARE DRIVE

RAID0RAID1RAID5RAID10

SPARE DRIVECONCATENATION

MAIN MENU

Auto configurationManual configuration

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -395 -395 -395 -395 -39

c. Repeat step b toselect the targetdrive.

d. After selectingthe source andtarget drives, thefollowing pop-upmenu appears.

Manual conf igurat ionManual conf igurat ionManual conf igurat ionManual conf igurat ionManual conf igurat ion

a. Select Manua lManua lManua lManua lManua lconf igurat ionconf igurat ionconf igurat ionconf igurat ionconf igurat ion andpress <Enter>. Theselectionbar moves tothe Physical Drives menu.

b. Using the up or downarrow keys, select thesource drIive and press<Enter>.

3. Select your desired method of configuration.Auto conf igurat ionAuto conf igurat ionAuto conf igurat ionAuto conf igurat ionAuto conf igurat iona. Select Auto Configuration then press <Enter>.b. The utility prompts a message to input the RAID size, use the up

or down arrow keys to set the RAID size then press <Enter>.c. Press <Y> to confirm or <N> to return to the Main Menu.

• Auto-configuration creates a RAID 1 set without a backup copy ofthe current source disk data.

• When migrating a single hard disk drive to a RAID 1 set, use of theManual configuration is recommended.

• The Create w i th data copyCreate w i th data copyCreate w i th data copyCreate w i th data copyCreate w i th data copy option allows you to copy thecurrent data from the source drive to the mirror drive.

• Select Create w i th data copy Create w i th data copy Create w i th data copy Create w i th data copy Create w i th data copy if you have important data inyour source drive.

• The Create w i thout data copy Create w i thout data copy Create w i thout data copy Create w i thout data copy Create w i thout data copy option disables the disk copyfunction of the Mirrored set.

• If you selected Create w i thout data copyCreate w i thout data copyCreate w i thout data copyCreate w i thout data copyCreate w i thout data copy, the RAID 1 setmust be repartitioned and reformatted to guarantee theconsistency of its contents.

PHYSICAL DRIVE

0 XXXXXXXXXXX XXXXXXMB1 XXXXXXXXXXX XXXXXXMB2 XXXXXXXXXXX XXXXXXMB3 XXXXXXXXXXX XXXXXXMB

MAIN MENU

Auto configurationManual configuration

Create with data copyCreate without data copy

5 -405 -405 -405 -405 -40 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

e. If you selectedCreate withCreate withCreate withCreate withCreate withdata copydata copydata copydata copydata copy, thefollowing pop-upmenu appears.

The on l i ne copyon l i ne copyon l i ne copyon l i ne copyon l i ne copy option automatically copies the data to the targetdrives on the background while writing to the source drives. Theof f l i ne copyof f l i ne copyof f l i ne copyof f l i ne copyof f l i ne copy option allows you to copy the contents of the sourcedrive to the target drives now.

f. Use the up or down arrow keys to select desired copy method,then press <Enter>.

g. The utility prompts a message to input the RAID size, use the upor down arrow keys to set the RAID size then press <Enter>.

h. Press <Y> to confirm or <N> to return to the Main Menu.

A copy progress appears if you previously selected offline copy.

MAIN MENU

Auto configurationManual configuration

online copyoffline copy

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 5 -415 -415 -415 -415 -41

Creating a CONCATENATION setCreating a CONCATENATION setCreating a CONCATENATION setCreating a CONCATENATION setCreating a CONCATENATION setTo create a CONCATENATION set:

1. From the SiliconImage configurationutility main menu,select Create RAIDCreate RAIDCreate RAIDCreate RAIDCreate RAIDset se t se t se t se t then press<Enter>.

2. From the sub-menuSelectCONCATENATIONCONCATENATIONCONCATENATIONCONCATENATIONCONCATENATIONthen press <Enter>.

MAIN MENU

Create RAID setDelete RAID setRebuild Raid1 setResolve ConflictsLow Level FormatLogical Drive Info

RAID0RAID1RAID10

SPARE DRIVE

RAID0RAID1RAID5RAID10

SPARE DRIVECONCATENATION

• Configure a CONCATENATION set when using a single Serial ATAdrive; otherwise, the system will not recognize the drive.

• You can also create a RAID set using the SATARAID5 GUI utilityunder a Windows® environment.

PHYSICAL DRIVE

0 XXXXXXXXXXX XXXXXXMB1 XXXXXXXXXXX XXXXXXMB2 XXXXXXXXXXX XXXXXXMB3 XXXXXXXXXXX XXXXXXMB

3. The selection bar moves to thePhysical Drive menu. Using theup or down arrow keys, select adrive then press <Enter>to set a drive for the RAID set.

4. The utility prompts a messageto input the RAID size, use theup or down arrow keys to setthe RAID size then press <Enter>.

5. Press <Y> to confirm or <N> to return to the Main Menu.

5 -425 -425 -425 -425 -42 Chapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software supportChapter 5 : Software support

5.5 Creating a RAID driver diskA floppy disk with the RAID driver is required when installing Windows®

2000/XP operating system on a hard disk drive that is included in a RAIDset.

To create a RAID driver disk:

1. Boot your computer.2. Press <Del> during POST to enter the BIOS setup utility.3. Set the optical drive as the primary boot device.4. Save changes and exit BIOS.5. Insert the support CD into the optical drive.6. Press the any key when the system prompts “Press any key to boot

from the optical drive.” The following menu appears:

1) Make ULi RAID Driver Disk

2) Format Floppy Disk

3) FreeDOS command prompt

Please choose 1 ~ 3:_

7. Press <1> to create a RAID driver disk.8. Insert a formatted floppy disk into the floppy drive then press

<Enter>.9. Follow succeeding screen instructions to complete the process.

- OR -- OR -- OR -- OR -- OR -1. Start Windows® .2. Place the motherboard support CD into the optical drive.3. When the Dr ivers Dr ivers Dr ivers Dr ivers Dr ivers menu appears, click Make ULi Chipset Dr iverMake ULi Chipset Dr iverMake ULi Chipset Dr iverMake ULi Chipset Dr iverMake ULi Chipset Dr iver

D i sk D i sk D i sk D i sk D i sk to create a ULI RAID driver disk.4. Insert a floppy disk into the floppy disk drive.5. Follow succeeding screen instructions to complete the process.

Write-protect the floppy disk to avoid computer virus infection.

To install the RAID driver:

1. During the OS installation, the system prompts you to press the F6key to install third-party SCSI or RAID driver.

2. Press <F6> then insert the floppy disk with RAID driver into the floppydisk drive.

3. Follow the succeeding screen instructions to complete the installation.

6This chapter tells how to installCrossFire™ graphics cards to avail ofATI’s Multi-Video Processingtechnology.

ATI CrossFire™technology

support

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE

Chapter summary 66.1 Overview............................................................................... 6-16.2 Hardware installation ............................................................ 6-26.3 Software information ........................................................... 6-5

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 6 - 16 - 16 - 16 - 16 - 1

6.1 OverviewThe motherboard supports the ATI CrossFire™ technology that allows youto install multi-graphics processing units (GPU) graphics cards. Follow theinstallation procedures in this section.

RequirementsRequirementsRequirementsRequirementsRequirements

• CrossFire™ Edition graphics card (Master)• CrossFire™-ready graphics card (Slave)• CrossFire™-ready motherboard, such as the ASUS A8R32-MVP DELUXE

motherboard.• Make sure that your power supply unit (PSU) can provide at least the

minimum power required by your system. See “7. Power connectors”on page 2-26 for details.

• Visit the ATI website or download the CrossFire™ Xpress 3200Edition User’s Guide from the support CD for detailed hardwarerequirements and installation procedures.

• The ATI CrossFire™ technology supports only the following operatingsystems:

- Windows® XP 32-bit (Home or Professional) with Service Pack 2 (SP2)- Windows® XP Professional 64-bit Edition.

• Make sure that your graphics card driver supports the ATICrossFire™ Technology. Download the latest driver from the ATIwebsite (www.ati.com)

• The maximum resolution of CrossFire™ Xpress 3200 Edition is 1600x 1200 at 65 MHz when you use DVI output.

Before you beginBefore you beginBefore you beginBefore you beginBefore you begin

Uninstall other graphics card driverUninstall other graphics card driverUninstall other graphics card driverUninstall other graphics card driverUninstall other graphics card drivers in your systems in your systems in your systems in your systems in your systemTo uninstall other graphics card drivers:

1. Close all current applications.2. Go to Contro l Panel > Add/Remove ProgramsControl Panel > Add/Remove ProgramsControl Panel > Add/Remove ProgramsControl Panel > Add/Remove ProgramsControl Panel > Add/Remove Programs.3. Select your current graphics card driver/s.4. Select Add/RemoveAdd/RemoveAdd/RemoveAdd/RemoveAdd/Remove.5. Restart your system.

6 - 26 - 26 - 26 - 26 - 2 Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : AT I CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy support

2. Insert the CrossFire™-ready (Master) graphics card into the blue slot.Make sure that the card is properly seated on the slot.

6.2 Hardware installation

Installing CrossFire™ graphics cardsInstalling CrossFire™ graphics cardsInstalling CrossFire™ graphics cardsInstalling CrossFire™ graphics cardsInstalling CrossFire™ graphics cards

Before installing a CrossFire™ system, refer to the user guide that camewith the ATI CrossFire™ Edition graphics card.

To install the graphics cards:

1. Prepare one CrossFire™ Edition graphics card, which will serve as theMaster graphics card, and one CrossFire™-ready graphics card, whichwill serve as the Slave graphics card.

Maste r g r aph i c s ca rdMas te r g r aph i c s ca rdMas te r g r aph i c s ca rdMas te r g r aph i c s ca rdMas te r g r aph i c s ca rd S l ave g raph i c s ca rdS l ave g raph i c s ca rdS l ave g raph i c s ca rdS l ave g raph i c s ca rdS l ave g raph i c s ca rd

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 6 - 36 - 36 - 36 - 36 - 3

4. Connect one end of the external cable to the Master graphics card.

3. Insert the CrossFire™ Edition (Slave) graphics card into the black slot.Make sure that the card is properly seated on the slot.

6 - 46 - 46 - 46 - 46 - 4 Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : AT I CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy support

5. Connect the other end of the external cable to the Slave graphicscard.

6. Connect the loose end to the corresponding port on your monitor.7. Connect an auxiliary power source from the power supply to the

graphics cards.

55555

66666

77777

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 6 - 56 - 56 - 56 - 56 - 5

6.3 Software information

6.3.16.3.16.3.16.3.16.3.1 Installing the device driversInstalling the device driversInstalling the device driversInstalling the device driversInstalling the device driversRefer to the documentation that came with your graphics card package toinstall the device drivers.

The ATI CrossFire™ technology supports only the following operatingsystems:

• Windows® XP 32-bit (Home or Professional) with ServicePack 2 (SP2)

• Windows® XP Professional 64-bit Edition.

1. Turn on your system and log inwith administrator rights.

2. Place the CrossFire™installation CD in your opticaldrive. The opening menuappears.Click Insta l l CrossF i reInsta l l CrossF i reInsta l l CrossF i reInsta l l CrossF i reInsta l l CrossF i redr iversdr iversdr iversdr iversdr ivers.

3. The installation windowappears. Click NextNextNextNextNext tocontinue.

4. Read the License Agreement,then click Y e sY e sY e sY e sY e s.

6 - 66 - 66 - 66 - 66 - 6 Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : AT I CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy support

5. Select the components thatyou want to install, then clickNextNextNextNextNext.

6. Installation begins.

7. A status window appears,indicating the progress of theinstallation.

8. The Setup CompleteSetup CompleteSetup CompleteSetup CompleteSetup Complete windowappears, indicating that thedriver files have been copied toyour computer.Click Y e sY e sY e sY e sY e s to restart yourcomputer now or N oN oN oN oN o to restartlater.Click F in i shF in i shF in i shF in i shF in i sh.

• Select Exp ressExp ressExp ressExp ressExp ress to install the HydraVision™ multi-monitor anddesktop management software, as well as the ATI driver.

• Select Cus tomCustomCustomCustomCustom to individually choose desired software components.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 6 - 76 - 76 - 76 - 76 - 7

6.3.26.3.26.3.26.3.26.3.2 Using the Catalyst™ Control CenterUsing the Catalyst™ Control CenterUsing the Catalyst™ Control CenterUsing the Catalyst™ Control CenterUsing the Catalyst™ Control CenterThe Catalyst™ Control Center allows you to access display features of theATI hardware and software you installed. Use this application to adjustyour graphic settings, enable/disable connected devices, and change yourdesktop orientation.

Launching the Catalyst™ Control CenterLaunching the Catalyst™ Control CenterLaunching the Catalyst™ Control CenterLaunching the Catalyst™ Control CenterLaunching the Catalyst™ Control Center

There are several ways to launch the Catalyst™ Control Center:

• On the Windows® task bar, click Start Start Start Start Start > ATI Catalyst™ ControlATI Catalyst™ ControlATI Catalyst™ ControlATI Catalyst™ ControlATI Catalyst™ ControlCenter Center Center Center Center > Catalyst™ Control CenterCatalyst™ Control CenterCatalyst™ Control CenterCatalyst™ Control CenterCatalyst™ Control Center

• Double-click the Catalyst™ Control Center desktopshortcut.

• On the Windows® task bar,double-click the Catalyst™ ControlCenter icon.

6 - 86 - 86 - 86 - 86 - 8 Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : AT I CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy support

The Catalyst™ Control Center Dialog BoxThe Catalyst™ Control Center Dialog BoxThe Catalyst™ Control Center Dialog BoxThe Catalyst™ Control Center Dialog BoxThe Catalyst™ Control Center Dialog BoxView

The Catalyst™ Control Center provides two views:

• Standard Standard Standard Standard Standard - simple view with wizards for beginners

• Advance Advance Advance Advance Advance - allows advanced users to access and configure the completefeatures of the software

• Set to Advance Advance Advance Advance Advance view to enable the CrossFire™ function.

• Make sure that the Dual-slot configuration item in the BIOS is set to[Auto] or [Dual Video Cards] if you want to enable the CrossFire™function.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 6 - 96 - 96 - 96 - 96 - 9

To enable CrossFire™:

1. Set the view to AdvanceAdvanceAdvanceAdvanceAdvance.2. Click the Crossf i re™ Crossf i re™ Crossf i re™ Crossf i re™ Crossf i re™ item in Graphics Sett ingsGraphics Sett ingsGraphics Sett ingsGraphics Sett ingsGraphics Sett ings.3. In the CrossFire™ Settings dialog, tick the box opposite Enab leEnab leEnab leEnab leEnab le

CrossF i re™CrossF i re™CrossF i re™CrossF i re™CrossF i re™.4. Click OK to effect the setting.

22222

33333

44444

Hotkeys

Click the Hotkeys Hotkeys Hotkeys Hotkeys Hotkeys tab on the Catalyst™ Control Center to access theHotkeys Manager, which allows you to create key combinations asshortcuts for performing certain functions quickly.

6 -106 -106 -106 -106 -10 Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : AT I CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy support

Profiles

Click the Prof i les Prof i les Prof i les Prof i les Prof i les tab on the Catalyst™ Control Center to access theProfiles Manager, which allows you to create customized environments foryour desktop, video, and 3D applications.

Preferences

Click the Preferences Preferences Preferences Preferences Preferences tab on the Catalyst™ Control Center to select alanguage, restore defaults, change skins, or enable/disable the SystemTray icon.

ASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXEASUS A8R32-MVP DELUXE 6 -116 -116 -116 -116 -11

Help

Click the He lp He lp He lp He lp He lp tab on the Catalyst™ Control Center to access the onlinehelp system, generate a Problem Report, and get the Catalyst™ ControlCenter version information.

The CrossF i re™CrossF i re™CrossF i re™CrossF i re™CrossF i re™ item in Graph ics Sett ingsGraph ics Sett ingsGraph ics Sett ingsGraph ics Sett ingsGraph ics Sett ings will not show up if themotherboard or the VGA card you use doesn’t support the CrossFire™system.

6 -126 -126 -126 -126 -12 Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : Chapter 6 : AT I CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy supportATI CrossF i re™ techno logy support

(PDF) A8R32-MVP Deluxe - Asusdlcdnet.asus.com/pub/ASUS/mb/socket939/A8R32-MVP... · viii Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power - PDFSLIDE.NET (2024)

References